Arduino 中 EEprom 写入读取清除

转自：https://www.arduino.cn/thread-1157-1-1.html

EEPROM (Electrically Erasable Programmable Read-Only Memory)，电可擦可编程只读存储器--一种掉电后数据不丢失的存储芯片。 简而言之就是你想断电后arduino还要保存一些参数，就使用EEPROM吧。 在各型号的arduino控制器上的AVR芯片均带有EEPROM，也有外接的EEPROM芯片，常见arduino控制器的EEPROM大小： Arduino UNO、Arduino duemilanove-m328、Zduino m328均使用ATmega328芯片，EEPROM都为1K Arduino duemilanove-m168的EEPROM为512bytes Arduino 2560的EEPROM为4K
下面我们介绍arduino自带的EEPROM使用方法，arduino的库已经为我们准备好了EEPROM类库，我们要使用得先调用EEPROM.h，然后使用write和read方法，即可操作EEPROM。 另：下面的官方例子由于写成较早，所以讲EEPROM的大小都定为了512字节，实际使用中，大家可参照上面所说的EEPROM大小，自行更改。
1.写入 选择 File>Examples>EEPROM>eeprom_write

kittenblock中小学创客名师推荐的图形化编程软件

	/*
	* EEPROM Write
	*
	* Stores values read from analog input 0 into the EEPROM.
	* These values will stay in the EEPROM when the board is
	* turned off and may be retrieved later by another sketch.
	*/
	#include <EEPROM.h>
	// EEPROM 的当前地址,即你将要写入的地址,这里就是从0开始写
	int addr = 0;
	void setup()
	{
	}
	void loop()
	{
	//模拟值读出后是一个0-1024的值，但每字节的大小为0-255，所以这里将值除以4再存储到val
	int val = analogRead(0) / 4;
	// write the value to the appropriate byte of the EEPROM.
	// these values will remain there when the board is
	// turned off.
	EEPROM.write(addr, val);
	// advance to the next address.  there are 512 bytes in
	// the EEPROM, so go back to 0 when we hit 512.
	addr = addr + 1;
	if (addr == 512)
	addr = 0;
	delay(100);
	}

2.读取 选择 File>Examples>EEPROM>eeprom_read

kittenblock中小学创客名师推荐的图形化编程软件

	/*
	* EEPROM Read
	*
	* Reads the value of each byte of the EEPROM and prints it
	* to the computer.
	* This example code is in the public domain.
	*/
	#include <EEPROM.h>
	// start reading from the first byte (address 0) of the EEPROM
	int address = 0;
	byte value;
	void setup()
	{
	// initialize serial and wait for port to open:
	Serial.begin(9600);
	while (!Serial) {
	; // wait for serial port to connect. Needed for Leonardo only
	}
	}
	void loop()
	{
	// read a byte from the current address of the EEPROM
	value = EEPROM.read(address);
	Serial.print(address);
	Serial.print(" ");
	Serial.print(value, DEC);
	Serial.println();
	// advance to the next address of the EEPROM
	address = address + 1;
	// there are only 512 bytes of EEPROM, from 0 to 511, so if we're
	// on address 512, wrap around to address 0
	if (address == 512)
	address = 0;
	delay(500);
	}

3.清除 选择 File>Examples>EEPROM>eeprom_clear 清除EEPROM的内容，其实就是把EEPROM中每一个字节写入0，因为只用清一次零，所以整个程序都在setup部分完成。

kittenblock中小学创客名师推荐的图形化编程软件

	/* * EEPROM Clear
	*
	* Sets all of the bytes of the EEPROM to 0.
	* This example code is in the public domain.
	*/
	#include <EEPROM.h>
	void setup()
	{
	// 让EEPROM的512字节内容全部清零
	for (int i = 0; i < 512; i++)
	EEPROM.write(i, 0);
	// 清零工作完成后，将L灯点亮，提示EEPROM清零完成
	digitalWrite(13, HIGH);
	}
	void loop()
	{
	}