zoukankan      html  css  js  c++  java
  • POJ 1523 Tarjan求割点

    SPF

    Description

    Consider the two networks shown below. Assuming that data moves around these networks only between directly connected nodes on a peer-to-peer basis, a failure of a single node, 3, in the network on the left would prevent some of the still available nodes from communicating with each other. Nodes 1 and 2 could still communicate with each other as could nodes 4 and 5, but communication between any other pairs of nodes would no longer be possible.

    Node 3 is therefore a Single Point of Failure (SPF) for this network. Strictly, an SPF will be defined as any node that, if unavailable, would prevent at least one pair of available nodes from being able to communicate on what was previously a fully connected network. Note that the network on the right has no such node; there is no SPF in the network. At least two machines must fail before there are any pairs of available nodes which cannot communicate.
    这里写图片描述
    Input

    The input will contain the description of several networks. A network description will consist of pairs of integers, one pair per line, that identify connected nodes. Ordering of the pairs is irrelevant; 1 2 and 2 1 specify the same connection. All node numbers will range from 1 to 1000. A line containing a single zero ends the list of connected nodes. An empty network description flags the end of the input. Blank lines in the input file should be ignored.
    Output

    For each network in the input, you will output its number in the file, followed by a list of any SPF nodes that exist.

    The first network in the file should be identified as “Network #1”, the second as “Network #2”, etc. For each SPF node, output a line, formatted as shown in the examples below, that identifies the node and the number of fully connected subnets that remain when that node fails. If the network has no SPF nodes, simply output the text “No SPF nodes” instead of a list of SPF nodes.
    Sample Input

    1 2
    5 4
    3 1
    3 2
    3 4
    3 5
    0

    1 2
    2 3
    3 4
    4 5
    5 1
    0

    1 2
    2 3
    3 4
    4 6
    6 3
    2 5
    5 1
    0

    0
    Sample Output

    Network #1
    SPF node 3 leaves 2 subnets

    Network #2
    No SPF nodes

    Network #3
    SPF node 2 leaves 2 subnets
    SPF node 3 leaves 2 subnets

    原题请戳这里
    题意:
    给定一个连通网络,网络的结点数<=1000,求出这个网络的所有割点编号,并求出若删去其中一个割点后,原网络会被分割为多少个互不相连的部分?
    tips:
    1.每组数据后输出空行
    2.按顺序输出
    3.图有可能不连通 Tarjan的时候不能把1当做root节点了。。。

    #include <cstdio>
    #include <vector>
    #include <cstring>
    #include <algorithm>
    using namespace std;
    int low[1005],dfn[1005],vis[1005],tot=1,T=1,n,m,q=0,W,cnt,root;
    vector <int> v[1005];
    void tarjan(int x){
        dfn[x]=low[x]=tot++,vis[x]=1;
        for(int i=0;i<v[x].size();i++)
            if(!vis[v[x][i]]){
                tarjan(v[x][i]),low[x]=min(low[x],low[v[x][i]]);
                if(dfn[x]<=low[v[x][i]]) vis[x]++;
            }
            else low[x]=min(low[x],dfn[v[x][i]]);
        if((x==root&&vis[x]>2)||(x!=root&&vis[x]>1)) vis[x]=2,v[1001].push_back(x);
        else vis[x]=1;
    }
    void dfs(int x){
        vis[x]=1;
        for(int i=0;i<v[x].size();i++){
            if(v[x][i]==W||x==W)continue;
            if(!vis[v[x][i]])dfs(v[x][i]);
        }
    }
    int main()
    {
        while(scanf("%d",&n)&&n)
        start:  scanf("%d",&m),q=max(q,max(n,m)),v[n].push_back(m),v[m].push_back(n);
        printf("Network #%d
    ",T);
        for(int i=1;i<=q;i++)
            if(!dfn[i])root=i,tarjan(i);
        if(v[1001].size()==0)printf("  No SPF nodes
    ");
        sort(v[1001].begin(),v[1001].end());
        for(int i=0;i<v[1001].size();i++){
            memset(vis,0,sizeof(vis));cnt=0;
            W=v[1001][i];
            for(int j=1;j<=q;j++)
                if(!vis[j])vis[j]=1,dfs(j),cnt++;
            printf("  SPF node %d leaves %d subnets
    ",W,cnt-1);
        }
        for(int i=1;i<=q;i++) v[i].clear();
        v[1001].clear();
        q=0;tot=1;T++;
        memset(low,0,sizeof(low)),memset(dfn,0,sizeof(dfn)),memset(vis,0,sizeof(vis));
        printf("
    ");
        scanf("%d",&n);
        if(n)goto start;
    }

    这里写图片描述

  • 相关阅读:
    请教visiouml活动图中动作状态和状态的区别谢谢 软件工程管理 软件规划版
    !!!IT人员迅速提升自我效率的十大方法
    如何在Visio的UML活动图中(判断及控制流)添加文字啊????
    Convert Standard String to System::String
    m_pRecordset遍历记录集之后,m_pRecordsetMoveFirst()为什么会出错
    !!! C++/CLI中使用using namespace System::Windows::Forms;+MessageBox报错最重要的是看MSDN 每个函数的使用例子
    !!!创建 UML 活动图 Visio Office_com
    C#反射之AssemblyCLR/c++可以通过反射调用c#类库
    请允许我进入你的世界
    以赛庆党日
  • 原文地址:https://www.cnblogs.com/SiriusRen/p/6532480.html
Copyright © 2011-2022 走看看