[USB]USB类代码备份[转]

原始链接1：http://www.usb.org/developers/defined_class （USB官方论坛）

原始链接2：http://www.baiheee.com/Documents/090518/090518112619.htm （百合电子）

Home > Developers > Defined 1.0 Class Codes

USB Class Codes                    

December 7, 2011

USB defines class code information that is used to identify a device’s functionality and to nominally load a device driver based on that functionality. The information is contained in three bytes with the names Base Class, SubClass, and Protocol. (Note that ‘Base Class’ is used in this description to identify the first byte of the Class Code triple. That terminology is not used in the USB Specification). There are two places on a device where class code information can be placed.One place is in the Device Descriptor, and the other is in Interface Descriptors. Some defined class codes are allowed to be used only in a Device Descriptor, others can be used in both Device and Interface Descriptors, and some can only be used in Interface Descriptors. The table below shows the currently defined set of  Base Class values, what the generic usage is, and where that Base Class can be used (either Device or Interface Descriptors or both).

 

Base Class	Descriptor Usage	Description
00h	Device	Use class information in the Interface Descriptors
01h	Interface	Audio
02h	Both	Communications and CDC Control
03h	Interface	HID (Human Interface Device)
05h	Interface	Physical
06h	Interface	Image
07h	Interface	Printer
08h	Interface	Mass Storage
09h	Device	Hub
0Ah	Interface	CDC-Data
0Bh	Interface	Smart Card
0Dh	Interface	Content Security
0Eh	Interface	Video
0Fh	Interface	Personal Healthcare
10h	Interface	Audio/Video Devices
DCh	Both	Diagnostic Device
E0h	Interface	Wireless Controller
EFh	Both	Miscellaneous
FEh	Interface	Application Specific
FFh	Both	Vendor Specific

Base Class 00h (Device)

This base class is defined to be used in Device Descriptors to indicate that class information should be determined from the Interface Descriptors in the device. There is one class code definition in this base class. All other values are reserved.

 

This value is also used in Interface Descriptors to indicate a null class code triple.

 

Base Class	SubClass	Protocol	Meaning
00h	00h	00h	Use class code info from Interface Descriptors

 

Base Class 01h (Audio)

This base class is defined for Audio capable devices that conform to the Audio Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.Values outside of that defined spec are reserved. These class codes may only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
01h	xxh	xxh	Audio device

 

 

Base Class 02h (Communications and CDC Control)

 

This base class is defined for devices that conform to the Communications Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved.  Note that the Communication Device Class spec requires some class code values (triples) to be used in Device Descriptors and some to be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
02h	xxh	xxh	Communication device class

 

Base Class 03h (HID – Human Interface Device)

This base class is defined for devices that conform to the HID Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.   Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
03h	xxh	xxh	HID device class

 

Base Class 05h (Physical)

This base class is defined for devices that conform to the Physical Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.  Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
05h	xxh	xxh	Physical device class

 

 

Base Class 06h (Still Imaging)

This base class is defined for devices that conform to the Imaging Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.   Values outside of that defined spec are reserved.

 

Base Class	SubClass	Protocol	Meaning
06h	01h	01h	Still Imaging device

 

 

Base Class 07h (Printer)

This base class is defined for devices that conform to the Printer Device Class Specification found on the USB-IF website.  That specification defines the usable set of SubClass and Protocol values.  Values outside of that defined spec are reserved.  These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
07h	xxh	xxh	Printer device

 

 

Base Class 08h (Mass Storage)

This base class is defined for devices that conform to the Mass Storage Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
08h	xxh	xxh	Mass Storage device

 

 

Base Class 09h (Hub)

This base class is defined for devices that are USB hubs and conform to the definition in the USB specification.  That specification defines the complete triples as shown below.  All other values are reserved.  These class codes can only be used in Device Descriptors.

 

Base Class	SubClass	Protocol	Meaning
09h	00h	00h	Full speed Hub
		01h	Hi-speed hub with single TT
		02h	Hi-speed hub with multiple TTs

 

 

Base Class 0Ah (CDC-Data)

This base class is defined for devices that conform to the Communications Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
0Ah	xxh	xxh	CDC data device

 

 

Base Class 0Bh (Smart Card)

This base class is defined for devices that conform to the Smart Card Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values.Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
0Bh	xxh	xxh	Smart Card device

 

 

Base Class 0Dh (Content Security)

This base class is defined for devices that conform to the Content Security Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
0Dh	00h	00h	Content Security device

 

 

Base Class 0Eh (Video)

This base class is defined for devices that conform to the Video Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
0Eh	xxh	xxh	Video device

 

Base Class 0Fh (Personal Healthcare)

This base class is defined for devices that conform to the Personal Healthcare Device Class Specification found on the USB-IF website. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved. These class codes should only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
0Fh	xxh	xxh	Personal Healthcare device

Base Class 10h (Audio/Video Devices)

The USB Audio/Video (AV) Device Class Definition describes the methods used to communicate with devices or functions embedded in composite devices that are used to manipulate audio, video, voice, and all image- and sound-related functionality. That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved. These class codes can only be used in Interface Descriptors. 

Base Class	SubClass	Protocol	Meaning
10h	01h   02h   03h	00h	Audio/Video Device – AVControl Interface
		00h	Audio/Video Device – AVData Video Streaming Interface
		00h	Audio/Video Device – AVData Audio Streaming Interface

  

Base Class DCh (Diagnostic Device)

This base class is defined for devices that diagnostic devices. There is currently only one value defined. All other values are reserved. This class code can be used in Device or Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
DCh	01h	01h	USB2 Compliance Device.  Definition for this device can be found athttp://www.intel.com/technology/usb/spec.htm

 

 

Base Class E0h (Wireless Controller)

This base class is defined for devices that are Wireless controllers. Values not shown in the table below are reserved. These class codes are to be used in Interface Descriptors, with the exception of the Bluetooth class code which can also be used in a Device Descriptor. 

Base Class	SubClass	Protocol	Meaning
E0h	01h	01h	Bluetooth Programming Interface.  Get specific information fromwww.bluetooth.com.
		02h	UWB Radio Control Interface.  Definition for this is found in the Wireless USB Specification in Chapter 8.
		03h	Remote NDIS.  Information can be found at:http://www.microsoft.com/windowsmobile/mobileoperators/default.mspx
		04h	Bluetooth AMP Controller. Get specific information fromwww.bluetooth.com.
	2h	01h	Host Wire Adapter Control/Data interface.  Definition can be found in the Wireless USB Specification in Chapter 8.
		02h	Device Wire Adapter Control/Data interface.  Definition can be found in the Wireless USB Specification in Chapter 8.
		03h	Device Wire Adapter Isochronous interface.  Definition can be found in the Wireless USB Specification in Chapter 8.

 

Base Class EFh (Miscellaneous)

This base class is defined for miscellaneous device definitions. Values not shown in the table below are reserved. The use of these class codes (Device or Interface descriptor) are specifically annotated in each entry below.

Base Class	SubClass	Protocol	Meaning
EFh	01h	01h	Active Sync device. This class code can be used in either Device or Interface Descriptors. Contact Microsoft for more information on this class.
		02h	Palm Sync. This class code can be used in either Device or Interface Descriptors.
	02h	01h	Interface Association Descriptor. The usage of this class code triple is defined in the Interface Association Descriptor ECN that is provided on www.usb.org . This class code may only be used in Device Descriptors.
		02h	Wire Adapter Multifunction Peripheral programming interface. Definition can be found in the Wireless USB Specification in Chapter 8. This class code may only be used in Device Descriptors
	03h	01h	Cable Based Association Framework. This is defined in the Association Model addendum to the Wireless USB specification. This class code may only be used in Interface Descriptors.
	04h	01h	RNDIS over Ethernet. Connecting a host to the Internet via Ethernet mobile device. The device appears to the host as an Ethernet gateway device. This class code may only be used in Interface Descriptors.
		02h	RNDIS over WiFi. Connecting a host to the Internet via WiFi enabled mobile device.  The device represents itself to the host as an 802.11 compliant network device. This class code may only be used in Interface Descriptors.
		03h	RNDIS over WiMAX Connecting a host to the Internet via WiMAX enabled mobile device.  The device is represented to the host as an 802.16 network device. This class code may only be used in Interface Descriptors.
		04h	RNDIS over WWAN Connecting a host to the Internet via a device using mobile broadband, i.e. WWAN (GSM/CDMA). This class code may only be used in Interface Descriptors.
		05h	RNDIS for Raw IPv4 Connecting a host to the Internet using raw IPv4 via non-Ethernet mobile device.  Devices that provide raw IPv4, not in an Ethernet packet, may use this form to in lieu of other stock types. This class code may only be used in Interface Descriptors.
		06h	RNDIS for Raw IPv6 Connecting a host to the Internet using raw IPv6 via non-Ethernet mobile device.  Devices that provide raw IPv6, not in an Ethernet packet, may use this form to in lieu of other stock types. This class code may only be used in Interface Descriptors.
		07h	RNDIS for GPRS Connecting a host to the Internet over GPRS mobile device using the device’s cellular radio
	05h	00h	USB3 Vision Control Interface	Machine Vision Device conforming to the USB3 Vision specification. This standard covers cameras and other related devices that are typically used in machine vision, industrial, and embedded applications. Reference:http://visiononline.org/ This class code may only be used in Interface Descriptors.
		01h	USB3 Vision Event Interface
		02h	USB3 Vision Streaming Interface

Base Class FEh (Application Specific)

This base class is defined for devices that conform to several class specifications found on the USB-IF website.  That specification defines the usable set of SubClass and Protocol values. Values outside of that defined spec are reserved.  These class codes can only be used in Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
FEh	01h	01h	Device Firmware Upgrade.  Device class definition provided on www.usb.org .
	02h	00h	IRDA Bridge device.  Device class definition provided on www.usb.org .
	03h	00h	USB Test and Measurement Device. Definition provided in the USB Test and Measurement Class spec found onwww.usb.org .
		01h	USB Test and Measurement Device conforming to the USBTMC USB488 Subclass Specification found on www.usb.org.

 

 

Base Class FFh (Vendor Specific)

This base class is defined for vendors to use as they please.  These class codes can be used in both Device and Interface Descriptors.

 

Base Class	SubClass	Protocol	Meaning
FFh	xxh	xxh	Vendor specific

 

/************************5是分割线***********************************************************************/

表10、USB接口描述符的结构
偏移量	域	大小	值	说明
0	bLength	1	数字	此表的字节数
1	bDescriptorType	1	常量	接口描述表类（此处应为0x04）
2	bInterfaceNumber	1	数字	接口号，当前配置支持的接口数组索引（从零开始）。
3	bAlternateSetting	1	数字	可选设置的索引值。
4	bNumEndpoints	1	数字	此接口用的端点数量，如果是零则说明此接口只用缺省控制管道。
5	bInterfaceClass	1	类	接口所属的类值：  零值为将来的标准保留。  如果此域的值设为FFH，则此接口类由厂商说明。  所有其它的值由USB 说明保留。
6	bInterfaceSubClass	1	子类	子类码  这些值的定义视bInterfaceClass域而定。 如果bInterfaceClass域的值为零则此域的值必须为零。  bInterfaceClass域不为FFH则所有值由USB 所保留。
7	bInterfaceProtocol	1	协议	协议码：bInterfaceClass 和bInterfaceSubClass 域的值而定.如果一个接口支持设备类相关的请求此域的值指出了设备类说明中所定义的协议.
8	iInterface	1	索引	描述此接口的字串描述表的索引值。

对于bInterfaceClass字段，表示接口所属的类别，USB协议根据功能将不同的接口划分成不的类，其具体含义如下表所示：

表11、USB协议定义的接口类别（bInterfaceClass）
值（十六进制）	类别
0x01	音频类
0x02	CDC控制类
0x03	人机接口类（HID）
0x05	物理类
0x06	图像类
0x07	打印机类
0x08	大数据存储类
0x09	集线器类
0x0A	CDC数据类
0x0B	智能卡类
0x0D	安全类
0xDC	诊断设备类
0xE0	无线控制器类
0xFE	特定应用类（包括红外的桥接器等）
0xFF	厂商定义的设备