相比于一通道，原子的例程里因为清了计数时间，所以要对程序进行修改。
记录上升沿后的计数，然后记录下降沿的计数。相减后计算高电平时间，对于定时器中断间隔的边界要分开处理。
这里因为我的接收机时间是1ms~2ms，而中断时间设置为20ms。所以根本不需要考虑时间延迟超过计时器时间。
下面是我的代码
//arr:自动重装值 psc:时钟预分频数 //定时器溢出时间计算：Tout=((arr+1)*(psc+1))/Ft us //Ft = 定时器工作频率，单位Mhz //TIM2在APB1上，为HCLK/2 36Mhz void TIM2_CAP_Init(u16 arr, u16 psc) { GPIO_InitTypeDef GPIO_InitStruct; TIM_TimeBaseInitTypeDef TIM_TimeBaseInitStruct; TIM_ICInitTypeDef TIM_ICInitStruct; NVIC_InitTypeDef NVIC_InitStruct; //开启TIM2和GPIO时钟 RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE); RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE); //PA0初始化 GPIO_InitStruct.GPIO_Mode = GPIO_Mode_IPD; //下拉输入 GPIO_InitStruct.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3; GPIO_InitStruct.GPIO_Speed = GPIO_Speed_50MHz; GPIO_Init(GPIOA, &GPIO_InitStruct); //TIM2定时器初始化 TIM_TimeBaseInitStruct.TIM_Period = arr; TIM_TimeBaseInitStruct.TIM_Prescaler = psc; TIM_TimeBaseInitStruct.TIM_ClockDivision = TIM_CKD_DIV1; TIM_TimeBaseInitStruct.TIM_CounterMode = TIM_CounterMode_Up; //向上计数 TIM_TimeBaseInit(TIM2, &TIM_TimeBaseInitStruct); //TIM2_CH1输入捕获初始化 TIM_ICInitStruct.TIM_Channel = TIM_Channel_1; TIM_ICInitStruct.TIM_ICFilter = 0x00; //不滤波 TIM_ICInitStruct.TIM_ICPolarity = TIM_ICPolarity_Rising; //上升沿捕获 TIM_ICInitStruct.TIM_ICPrescaler = TIM_ICPSC_DIV1; //输入器不分频 TIM_ICInitStruct.TIM_ICSelection = TIM_ICSelection_DirectTI; //映射到IC1 TIM_ICInit(TIM2, &TIM_ICInitStruct); TIM_ICInitStruct.TIM_Channel = TIM_Channel_2; TIM_ICInitStruct.TIM_ICFilter = 0x00; //不滤波 TIM_ICInitStruct.TIM_ICPolarity = TIM_ICPolarity_Rising; //上升沿捕获 TIM_ICInitStruct.TIM_ICPrescaler = TIM_ICPSC_DIV1; //输入器不分频 TIM_ICInitStruct.TIM_ICSelection = TIM_ICSelection_DirectTI; //映射到IC2 TIM_ICInit(TIM2, &TIM_ICInitStruct); TIM_ICInitStruct.TIM_Channel = TIM_Channel_3; TIM_ICInitStruct.TIM_ICFilter = 0x00; //不滤波 TIM_ICInitStruct.TIM_ICPolarity = TIM_ICPolarity_Rising; //上升沿捕获 TIM_ICInitStruct.TIM_ICPrescaler = TIM_ICPSC_DIV1; //输入器不分频 TIM_ICInitStruct.TIM_ICSelection = TIM_ICSelection_DirectTI; //映射到IC3 TIM_ICInit(TIM2, &TIM_ICInitStruct); TIM_ICInitStruct.TIM_Channel = TIM_Channel_4; TIM_ICInitStruct.TIM_ICFilter = 0x00; //不滤波 TIM_ICInitStruct.TIM_ICPolarity = TIM_ICPolarity_Rising; //上升沿捕获 TIM_ICInitStruct.TIM_ICPrescaler = TIM_ICPSC_DIV1; //输入器不分频 TIM_ICInitStruct.TIM_ICSelection = TIM_ICSelection_DirectTI; //映射到IC4 TIM_ICInit(TIM2, &TIM_ICInitStruct); //中断分组初始化 NVIC_InitStruct.NVIC_IRQChannel = TIM2_IRQn; NVIC_InitStruct.NVIC_IRQChannelCmd = ENABLE; NVIC_InitStruct.NVIC_IRQChannelPreemptionPriority = 2; NVIC_InitStruct.NVIC_IRQChannelSubPriority = 0; NVIC_Init(&NVIC_InitStruct); TIM_ITConfig(TIM2, TIM_IT_CC1|TIM_IT_CC2|TIM_IT_CC3|TIM_IT_CC4, ENABLE); //更新中断和CC1IE捕获中断 TIM_Cmd(TIM2, ENABLE); printf("Init TIM2 CAP success "); }
然后是中断处理函数
//捕获状态 //[7]:0,没有成功捕获；1,成功捕获到一次 //[6]:0,还没捕获到低电平;1,已经捕获到低电平了. //[5:0]:捕获低电平后溢出第次数 u8 CAPTURE_STA_TIM2CH[4] = {0}; u16 CAPTURE_VAL_TIM2CH[4]; u16 CAPTURE_UP_TIM2CH[4], CAPTURE_DOWN_TIM2CH[4]; void TIM2_IRQHandler(void) { // if(TIM_GetITStatus(TIM2, TIM_IT_Update) != RESET) { // if((CAPTURE_STA_TIM2CH[1]&0x80) == 0) { //还未捕获成功 // if(CAPTURE_STA_TIM2CH[1]&0x40) { //已经捕获到高电平了 // if((CAPTURE_STA_TIM2CH[1]&0x3F)==0x3F) { //高电平太长了 // CAPTURE_STA_TIM2CH[1] |= 0x80; //标记成功捕获了一次 // CAPTURE_VAL_TIM2CH[1] = 0xFFFF; // } else // CAPTURE_VAL_TIM2CH[1]++; // } // } // TIM_ClearITPendingBit(TIM2, TIM_IT_Update); // } if((CAPTURE_STA_TIM2CH[0]&0x80) == 0) { //还未捕获成功 if(TIM_GetITStatus(TIM2, TIM_IT_CC1) != RESET) { //捕获1发生捕获事件 if(CAPTURE_STA_TIM2CH[0]&0x40) { //捕获到一个下降沿 CAPTURE_STA_TIM2CH[0] |= 0x80; //标记成功捕获到一次高电平脉宽 CAPTURE_DOWN_TIM2CH[0] = TIM_GetCapture1(TIM2); if(CAPTURE_DOWN_TIM2CH[0] >= CAPTURE_UP_TIM2CH[0]) CAPTURE_VAL_TIM2CH[0] = CAPTURE_DOWN_TIM2CH[0] - CAPTURE_UP_TIM2CH[0]; else CAPTURE_VAL_TIM2CH[0] = 0xffff + CAPTURE_DOWN_TIM2CH[0] - CAPTURE_UP_TIM2CH[0]; TIM_OC1PolarityConfig(TIM2, TIM_ICPolarity_Rising); //CC1P=0 设置为上升沿捕获 } else { //还未开始，第一次捕获上升沿 CAPTURE_STA_TIM2CH[0] = 0; //清空 CAPTURE_VAL_TIM2CH[0] = 0; CAPTURE_UP_TIM2CH[0] = TIM_GetCapture1(TIM2); CAPTURE_STA_TIM2CH[0] |= 0x40; //标记捕获到了上升沿 TIM_OC1PolarityConfig(TIM2, TIM_ICPolarity_Falling); //CC1P=1 设置为下降沿捕获 } TIM_ClearFlag(TIM2, TIM_FLAG_CC1); //清除状态标志 } } if((CAPTURE_STA_TIM2CH[1]&0x80) == 0) { //还未捕获成功 if(TIM_GetITStatus(TIM2, TIM_IT_CC2) != RESET) { //捕获2发生捕获事件 if(CAPTURE_STA_TIM2CH[1]&0x40) { //捕获到一个下降沿 CAPTURE_STA_TIM2CH[1] |= 0x80; //标记成功捕获到一次高电平脉宽 CAPTURE_DOWN_TIM2CH[1] = TIM_GetCapture2(TIM2); //获取捕获2计数 if(CAPTURE_DOWN_TIM2CH[1] >= CAPTURE_UP_TIM2CH[1]) CAPTURE_VAL_TIM2CH[1] = CAPTURE_DOWN_TIM2CH[1] - CAPTURE_UP_TIM2CH[1]; else CAPTURE_VAL_TIM2CH[1] = 0xffff + CAPTURE_DOWN_TIM2CH[1] - CAPTURE_UP_TIM2CH[1]; TIM_OC2PolarityConfig(TIM2, TIM_ICPolarity_Rising); //CC1P=0 设置为上升沿捕获 } else { //还未开始，第一次捕获上升沿 CAPTURE_STA_TIM2CH[1] = 0; //清空 CAPTURE_VAL_TIM2CH[1] = 0; CAPTURE_UP_TIM2CH[1] = TIM_GetCapture2(TIM2); CAPTURE_STA_TIM2CH[1] |= 0x40; //标记捕获到了上升沿 TIM_OC2PolarityConfig(TIM2, TIM_ICPolarity_Falling); //CC1P=1 设置为下降沿捕获 } TIM_ClearFlag(TIM2, TIM_FLAG_CC2); //清除状态标志 } } if((CAPTURE_STA_TIM2CH[2]&0x80) == 0) { //还未捕获成功 if(TIM_GetITStatus(TIM2, TIM_IT_CC3) != RESET) { //捕获2发生捕获事件 if(CAPTURE_STA_TIM2CH[2]&0x40) { //捕获到一个下降沿 CAPTURE_STA_TIM2CH[2] |= 0x80; //标记成功捕获到一次高电平脉宽 CAPTURE_DOWN_TIM2CH[2] = TIM_GetCapture3(TIM2); //获取捕获2计数 if(CAPTURE_DOWN_TIM2CH[2] >= CAPTURE_UP_TIM2CH[2]) CAPTURE_VAL_TIM2CH[2] = CAPTURE_DOWN_TIM2CH[2] - CAPTURE_UP_TIM2CH[2]; else CAPTURE_VAL_TIM2CH[2] = 0xffff + CAPTURE_DOWN_TIM2CH[2] - CAPTURE_UP_TIM2CH[2]; TIM_OC3PolarityConfig(TIM2, TIM_ICPolarity_Rising); //CC1P=0 设置为上升沿捕获 } else { //还未开始，第一次捕获上升沿 CAPTURE_STA_TIM2CH[2] = 0; //清空 CAPTURE_VAL_TIM2CH[2] = 0; CAPTURE_UP_TIM2CH[2] = TIM_GetCapture3(TIM2); CAPTURE_STA_TIM2CH[2] |= 0x40; //标记捕获到了上升沿 TIM_OC3PolarityConfig(TIM2, TIM_ICPolarity_Falling); //CC1P=1 设置为下降沿捕获 } TIM_ClearFlag(TIM2, TIM_FLAG_CC3); //清除状态标志 } } if((CAPTURE_STA_TIM2CH[3]&0x80) == 0) { //还未捕获成功 if(TIM_GetITStatus(TIM2, TIM_IT_CC4) != RESET) { //捕获2发生捕获事件 if(CAPTURE_STA_TIM2CH[3]&0x40) { //捕获到一个下降沿 CAPTURE_STA_TIM2CH[3] |= 0x80; //标记成功捕获到一次高电平脉宽 CAPTURE_DOWN_TIM2CH[3] = TIM_GetCapture4(TIM2); //获取捕获2计数 if(CAPTURE_DOWN_TIM2CH[3] >= CAPTURE_UP_TIM2CH[3]) CAPTURE_VAL_TIM2CH[3] = CAPTURE_DOWN_TIM2CH[3] - CAPTURE_UP_TIM2CH[3]; else CAPTURE_VAL_TIM2CH[3] = 0xffff + CAPTURE_DOWN_TIM2CH[3] - CAPTURE_UP_TIM2CH[3]; TIM_OC4PolarityConfig(TIM2, TIM_ICPolarity_Rising); //CC1P=0 设置为上升沿捕获 } else { //还未开始，第一次捕获上升沿 CAPTURE_STA_TIM2CH[3] = 0; //清空 CAPTURE_VAL_TIM2CH[3] = 0; CAPTURE_UP_TIM2CH[3] = TIM_GetCapture4(TIM2); CAPTURE_STA_TIM2CH[3] |= 0x40; //标记捕获到了上升沿 TIM_OC4PolarityConfig(TIM2, TIM_ICPolarity_Falling); //CC1P=1 设置为下降沿捕获 } TIM_ClearFlag(TIM2, TIM_FLAG_CC4); //清除状态标志 } } //处理帧数据 if(CAPTURE_STA_TIM2CH[0]&0x80) { //成功捕获到了一次上升沿 //溢出时间总和 myControl.remoteControl[0] = CAPTURE_VAL_TIM2CH[0]; //得到总的高电平时间 // printf("TIM2 CH1:%d ", temp[0]); CAPTURE_STA_TIM2CH[0] = 0; } if(CAPTURE_STA_TIM2CH[1]&0x80) { //成功捕获到了一次上升沿 //溢出时间总和 myControl.remoteControl[1] = CAPTURE_VAL_TIM2CH[1]; //得到总的高电平时间 // printf("TIM2 CH2:%d ", temp[1]); CAPTURE_STA_TIM2CH[1] = 0; } if(CAPTURE_STA_TIM2CH[2]&0x80) { //成功捕获到了一次上升沿 //溢出时间总和 myControl.remoteControl[2] = CAPTURE_VAL_TIM2CH[2]; //得到总的高电平时间 // printf("TIM2 CH3:%d ", temp[2]); CAPTURE_STA_TIM2CH[2] = 0; } if(CAPTURE_STA_TIM2CH[3]&0x80) { //成功捕获到了一次上升沿 //溢出时间总和 myControl.remoteControl[3] = CAPTURE_VAL_TIM2CH[3]; //得到总的高电平时间 // printf("TIM2 CH4:%d ", temp[3]); CAPTURE_STA_TIM2CH[3] = 0; } }
这些printf函数会极大的占用MCU资源，所以不在中断中处理。