zoukankan      html  css  js  c++  java
  • linux和windows手动添加路由条目命令

    如何 在windows添加一条静态路由

    1、添加一条路由表
    Route add 60.232.142.40 mask 255.255.255.248 192.168.100.250 metric 3 if 2
    添加一条路由记录,所有到60.232.142.40/29网段的数据包,都通过2号接口卡(网卡)走192.168.100.250的网关,优先级为3。(结果会怎样?)
    Route add –p 60.232.142.40 mask 255.255.255.248 192.168.100.250 metric 3 if 2
    作用同上,只是这是一条长久路由,不会因为重启机器而丢失。

    2、删除一条路由表
    Route delete 60.232.142.40
    请留心:如果有两条路由记录有着相同的“目的网络号”,则会将两条记录同时删除。如果只想删除其中某一条的话,请在删除后用route add命令再添加上其中一条。
    From:http://whatislinux.net/how-to-add-a-static-ip-route-in-windows

    3、修改一条路由记录
    Route change 157.0.0.0 mask 255.0.0.0 157.55.80.5 metric 2 if 2
    Change参数只能修改“网关”和“跳数”

     ---------------------

    linux下添加路由的方法

    技术学习/linux学习 2008/04/25 20:28

    linux下添加路由的方法:
    一:使用 route 命令添加
    使用route 命令添加的路由,机器重启或者网卡重启后路由就失效了,方法:
    //添加到主机的路由
    # route add –host 192.168.168.110 dev eth0
    # route add –host 192.168.168.119 gw 192.168.168.1
    //添加到网络的路由
    # route add –net IP netmask MASK eth0
    # route add –net IP netmask MASK gw IP
    # route add –net IP/24 eth1
    //添加默认网关
    # route add default gw IP
    //删除路由
    # route del –host 192.168.168.110 dev eth0
    二:在linux下设置永久路由的方法:
    1.在/etc/rc.local里添加
    方法:
    route add -net 192.168.3.0/24 dev eth0

    route add -net 192.168.2.0/24 gw 192.168.3.254


    2.在/etc/sysconfig/network里添加到末尾
    方法:GATEWAY=gw-ip 或者 GATEWAY=gw-dev

    3./etc/sysconfig/static-router :
    any net x.x.x.x/24 gw y.y.y.y

    linux添加路由

    路由, linux

    linux路由的添加对于我们来说很重要,有的时候网络不通,也许就是你路由没加,发出来,希望对大家有所帮助!

    服务器ip(eth0)
    [root@localhost net]# ifconfig
    eth0    Link encap:Ethernet   HWaddr 00:0C:29:E3:9A:15  
          inet addr:172.18.3.205   Bcast:172.18.3.255   Mask:255.255.255.0
          inet6 addr: fe80::20c:29ff:fee3:9a15/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST   MTU:1500   Metric:1
          RX packets:4776 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3348 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:439384 (429.0 KiB)   TX bytes:390425 (381.2 KiB)
          Interrupt:11 Base address:0x1400
    lo        Link encap:Local Loopback  
          inet addr:127.0.0.1   Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING   MTU:16436   Metric:1
          RX packets:254 errors:0 dropped:0 overruns:0 frame:0
          TX packets:254 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:22128 (21.6 KiB)   TX bytes:22128 (21.6 KiB)
      
      
    查看原始路由信息
    [root@localhost net]# route -n
    Kernel IP routing table
    Destination     Gateway       Genmask       Flags Metric Ref Use Iface
    172.18.3.0    0.0.0.0       255.255.255.0 U     0    0        0 eth0
    169.254.0.0     0.0.0.0       255.255.0.0     U     0    0        0 eth0
    ==========================================================
      
      
      
    添加默认网关
    [root@localhost net]# route add default gw 172.18.3.50
    [root@localhost net]# route
    Kernel IP routing table
    Destination     Gateway       Genmask       Flags Metric Ref Use Iface
    172.18.3.0    *             255.255.255.0 U     0    0        0 eth0
    169.254.0.0     *             255.255.0.0     U     0    0        0 eth0
    default       172.18.3.50     0.0.0.0       UG 0    0        0 eth0
    =======================================================
      
      
    添加一个ip(eth0:1)
    [root@localhost net]# ifconfig eth0:1 192.168.168.119 netmask 255.255.255.0 up
    [root@localhost net]# ifconfig
    eth0    Link encap:Ethernet   HWaddr 00:0C:29:E3:9A:15  
          inet addr:172.18.3.205   Bcast:172.18.3.255   Mask:255.255.255.0
          inet6 addr: fe80::20c:29ff:fee3:9a15/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST   MTU:1500   Metric:1
          RX packets:5071 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3569 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:466532 (455.5 KiB)   TX bytes:416538 (406.7 KiB)
          Interrupt:11 Base address:0x1400
    eth0:1 Link encap:Ethernet   HWaddr 00:0C:29:E3:9A:15  
          inet addr:192.168.168.119   Bcast:192.168.168.255   Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST   MTU:1500   Metric:1
          Interrupt:11 Base address:0x1400
    lo        Link encap:Local Loopback  
          inet addr:127.0.0.1   Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING   MTU:16436   Metric:1
          RX packets:258 errors:0 dropped:0 overruns:0 frame:0
          TX packets:258 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:22480 (21.9 KiB)   TX bytes:22480 (21.9 KiB)
      
    在查看路由信息
    [root@localhost net]# route -n
    Kernel IP routing table
    Destination     Gateway       Genmask       Flags Metric Ref Use Iface
    172.18.3.0    0.0.0.0       255.255.255.0 U     0    0        0 eth0
    192.168.168.0 0.0.0.0       255.255.255.0 U     0    0        0 eth0
    169.254.0.0     0.0.0.0       255.255.0.0     U     0    0        0 eth0
    0.0.0.0       172.18.3.50     0.0.0.0       UG 0    0        0 eth0
    ===============================================================
      
      
    添加一条到主机192.168.168.110的路由(通过eth0:1)
    [root@localhost net]# route add -host   192.168.168.110 dev eth0:1
    [root@localhost net]# route
    Kernel IP routing table
    Destination     Gateway       Genmask       Flags Metric Ref Use Iface
    192.168.168.110 *             255.255.255.255 UH 0    0        0 eth0
    172.18.3.0    *             255.255.255.0 U     0    0        0 eth0
    192.168.168.0 *             255.255.255.0 U     0    0        0 eth0
    169.254.0.0     *             255.255.0.0     U     0    0        0 eth0
    default       172.18.3.50     0.0.0.0       UG 0    0        0 eth0
    ===============================================================
      
      
    添加一条到主机192.168.168.120的路由(通过ip192.168.168.119)
    [root@localhost net]# route add -host 192.168.168.120 gw 192.168.168.119
    [root@localhost net]# route
    Kernel IP routing table
    Destination     Gateway       Genmask       Flags Metric Ref Use Iface
    192.168.168.120 192.168.168.119 255.255.255.255 UGH 0    0        0 eth0
    192.168.168.110 *     &nb

    sp;       255.255.255.255 UH 0    0        0 eth0
    172.18.3.0    *             255.255.255.0 U     0    0        0 eth0
    192.168.168.0 *             255.255.255.0 U     0    0        0 eth0
    169.254.0.0     *             255.255.0.0     U     0    0        0 eth0
    default       172.18.3.50     0.0.0.0       UG 0    0        0 eth0
    ===========================================================
    添加到网络的路由(通过eth0)
    [root@localhost net]# route add -net 192.168.3.0 netmask 255.255.255.0 dev eth0
    [root@localhost net]# route
    Kernel IP routing table
    Destination     Gateway       Genmask       Flags Metric Ref Use Iface
    192.168.168.120 192.168.168.119 255.255.255.255 UGH 0    0        0 eth0
    192.168.168.110 *             255.255.255.255 UH 0    0        0 eth0
    192.168.3.0     *             255.255.255.0 U     0    0        0 eth0
    172.18.3.0    *             255.255.255.0 U     0    0        0 eth0
    192.168.168.0 *             255.255.255.0 U     0    0        0 eth0
    169.254.0.0     *             255.255.0.0     U     0    0        0 eth0
    default       172.18.3.50     0.0.0.0       UG 0    0        0 eth0
      
    添加到网络的路由(通过ip172.18.3.50)
    [root@localhost net]# route add -net 192.168.4.0 netmask 255.255.255.0 gw 172.18.3.50
    [root@localhost net]# route
    Kernel IP routing table
    Destination     Gateway       Genmask       Flags Metric Ref Use Iface
    192.168.168.120 192.168.168.119 255.255.255.255 UGH 0    0        0 eth0
    192.168.168.110 *             255.255.255.255 UH 0    0        0 eth0
    192.168.4.0     172.18.3.50     255.255.255.0 UG 0    0        0 eth0
    192.168.3.0     *             255.255.255.0 U     0    0        0 eth0
    172.18.3.0    *             255.255.255.0 U     0    0        0 eth0
    192.168.168.0 *             255.255.255.0 U     0    0        0 eth0
    169.254.0.0     *             255.255.0.0     U     0    0        0 eth0
    default       172.18.3.50     0.0.0.0       UG 0    0        0 eth0
    =======================================================================
    参数区别-host跟主机ip,-net跟网络号
    =======================================================================
      
    输出结果中各个字段的含义是:
      
    Destination表示路由的目标IP地址
    Gateway表示网关使用的主机名或者是IP地址。上面输出的"*"表示没有网关
    Genmask表示路由的网络掩码
    Flags是表示路由的标志。可用的标志及其意义是:U表示路由在启动,H表示target是一台主机,G表示使用网关,R表示对动态路由进行复位设置;D表示动态安装路由,M表示修改路由,!表示拒绝路由。
    Metric表示路由的单位开销量
    Ref表示依赖本路由现状的其它路由数目
    Use表示路由表条目被使用的数目
    Iface表示路由所发送的包的目的网络

    本文来自思进网http://www.52sijin.com/ 转载请注明出处!

  • 相关阅读:
    初探element+vue+vue-router
    git命令移动文件夹到另一文件夹
    javascript最大公约数与最小公倍数
    求1-100数字的和
    [摘录]代码优化规则
    基于.NET平台常用的框架和开源程序整理
    软件架构师的12项修炼
    Service Oriented Architecture and WCF 【转】
    电商网站的初期技术选型【转】
    论SOA架构的几种主要开发方式【转】
  • 原文地址:https://www.cnblogs.com/kungfupanda/p/1753379.html
Copyright © 2011-2022 走看看