zoukankan      html  css  js  c++  java

  • 静态路由和默认路由配置

    GNS3图标

    不同网段之间可以通过路由器进行通信，但若是中间有多个路由器，在两三台的情况下，我们可以通过配置静态路由来实现数据转发。

    实验拓扑

    拓扑

    使用两台路由器直连，每台下面再连接一台VPC。地址规划如下：

    名称 接口 IP地址
    R1 f0/0 192.168.30.1/24
    R1 f0/1 192.168.10.1/24
    R2 f0/0 192.168.30.2/24
    R2 f0/1 192.168.20.1/24
    PC1 e0 192.168.10.10/24
    PC2 e0 192.168.20.10/24

    静态路由

    配置方法

    全局模式下添加一条静态路由。

    R1#configure terminal
R1(config)#ip route 192.168.20.0 255.255.255.0 192.168.30.2
    • 192.168.20.0：目的网段
    • 255.255.255.0：子网掩码
    • 192.168.30.2：下一跳

    配置过程

    R1

    • 配置f0/1接口ip地址
    R1#configure terminal
R1(config)#interface fastEthernet 0/1
R1(config-if)#ip address 192.168.10.1 255.255.255.0
R1(config-if)#no shutdown
R1(config-if)#exit
    • 配置f0/0接口ip地址
    R1(config)#interface fastEthernet 0/0
R1(config-if)#ip address 192.168.30.1 255.255.255.0
R1(config-if)#no shutdown
R1(config-if)#end
    • 查看接口地址及状态
    R1#show ip interface brief
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            192.168.30.1    YES manual up                    up
FastEthernet0/1            192.168.10.1    YES manual up                    up
    • 查看路由表
    R1#show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

C    192.168.30.0/24 is directly connected, FastEthernet0/0
C    192.168.10.0/24 is directly connected, FastEthernet0/1
    • 添加到达192.168.20.0网段的静态路由
    R1#configure terminal
R1(config)#ip route 192.168.20.0 255.255.255.0 192.168.30.2
R1(config)#end
    • 再次查看路由表
    R1#show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

C    192.168.30.0/24 is directly connected, FastEthernet0/0
C    192.168.10.0/24 is directly connected, FastEthernet0/1
S    192.168.20.0/24 [1/0] via 192.168.30.2

    R2

    • R2与R1的配置方法相同，以下为简写配置过程。
    R2#conf t
R2(config)#int f0/1
R2(config-if)#ip add 192.168.20.1 255.255.255.0
R2(config-if)#no sh
R2(config-if)#int f0/0
R2(config-if)#ip add 192.168.30.2 255.255.255.0
R2(config-if)#no sh
R2(config-if)#ex
R2(config)#ip route 192.168.10.0 255.255.255.0 192.168.30.1
R2(config)#do show ip int b
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            192.168.30.2    YES manual up                    up
FastEthernet0/1            192.168.20.1    YES manual up                    up
R2(config)#do show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

C    192.168.30.0/24 is directly connected, FastEthernet0/0
S    192.168.10.0/24 [1/0] via 192.168.30.1
C    192.168.20.0/24 is directly connected, FastEthernet0/1

    PING 测试

    配置 IP 地址

    PC1> ip 192.168.10.10 255.255.255.0 192.168.10.1
Checking for duplicate address...
PC1 : 192.168.10.10 255.255.255.0 gateway 192.168.10.1

    PC2> ip 192.168.20.10 192.168.20.1
Checking for duplicate address...
PC1 : 192.168.20.10 255.255.255.0 gateway 192.168.20.1

    PING

    PC1> ping 192.168.20.10
192.168.20.10 icmp_seq=1 timeout
192.168.20.10 icmp_seq=2 timeout
84 bytes from 192.168.20.10 icmp_seq=3 ttl=62 time=41.947 ms
84 bytes from 192.168.20.10 icmp_seq=4 ttl=62 time=39.882 ms
84 bytes from 192.168.20.10 icmp_seq=5 ttl=62 time=42.885 ms

    PC2> ping 192.168.10.10
84 bytes from 192.168.10.10 icmp_seq=1 ttl=62 time=38.025 ms
84 bytes from 192.168.10.10 icmp_seq=2 ttl=62 time=39.887 ms
84 bytes from 192.168.10.10 icmp_seq=3 ttl=62 time=43.782 ms
84 bytes from 192.168.10.10 icmp_seq=4 ttl=62 time=32.903 ms
84 bytes from 192.168.10.10 icmp_seq=5 ttl=62 time=38.942 ms

    通过配置静态路由成功使不同网段之间互通。

    默认路由

    默认路由是一种特殊的静态路由，当配置了默认路由，转发数据包中目的地址在路由表中没有相匹配的表项时，数据包将按默认路由转发，否则数据包会被丢弃。

    设想一：在R2上只配一条默认路由，是否可行？
    设想二：R1和R2都只配一条默认路由，是否可行？

    配置方法

    全局模式下添加一条默认路由。

    R2(config)#ip route 0.0.0.0 0.0.0.0 192.168.30.1
    • 0.0.0.0 0.0.0.0：代表任何网络
    • 192.168.30.1：下一跳

    设想一

    配置过程

    • R2删除添加的静态路由，添加默认路由。
    R2(config)#no ip route 192.168.10.0 255.255.255.0
R2(config)#ip route 0.0.0.0 0.0.0.0 192.168.30.1
R2(config)#do show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is 192.168.30.1 to network 0.0.0.0

C    192.168.30.0/24 is directly connected, FastEthernet0/0
C    192.168.20.0/24 is directly connected, FastEthernet0/1
S*   0.0.0.0/0 [1/0] via 192.168.30.1

    PING 测试

    PC1> ping 192.168.20.10
192.168.20.10 icmp_seq=1 timeout
192.168.20.10 icmp_seq=2 timeout
84 bytes from 192.168.20.10 icmp_seq=3 ttl=62 time=37.905 ms
84 bytes from 192.168.20.10 icmp_seq=4 ttl=62 time=34.870 ms
84 bytes from 192.168.20.10 icmp_seq=5 ttl=62 time=42.728 ms

    PC2> ping 192.168.10.10
84 bytes from 192.168.10.10 icmp_seq=1 ttl=62 time=38.995 ms
84 bytes from 192.168.10.10 icmp_seq=2 ttl=62 time=35.875 ms
84 bytes from 192.168.10.10 icmp_seq=3 ttl=62 time=36.911 ms
84 bytes from 192.168.10.10 icmp_seq=4 ttl=62 time=37.904 ms
84 bytes from 192.168.10.10 icmp_seq=5 ttl=62 time=35.912 ms

    通过PING测试，发现是可行的。

    设想二

    配置过程

    • 再在R1上删除添加的静态路由，添加默认路由。
    R1(config)#no ip route 192.168.20.0 255.255.255.0
R1(config)#ip route 0.0.0.0 0.0.0.0 192.168.30.2
R1(config)#do show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is 192.168.30.2 to network 0.0.0.0

C    192.168.30.0/24 is directly connected, FastEthernet0/0
C    192.168.10.0/24 is directly connected, FastEthernet0/1
S*   0.0.0.0/0 [1/0] via 192.168.30.2

    PING 测试

    PC1> ping 192.168.20.10
192.168.20.10 icmp_seq=1 timeout
192.168.20.10 icmp_seq=2 timeout
84 bytes from 192.168.20.10 icmp_seq=3 ttl=62 time=33.073 ms
84 bytes from 192.168.20.10 icmp_seq=4 ttl=62 time=36.042 ms
84 bytes from 192.168.20.10 icmp_seq=5 ttl=62 time=41.983 ms

    PC2> ping 192.168.10.10
84 bytes from 192.168.10.10 icmp_seq=1 ttl=62 time=43.736 ms
84 bytes from 192.168.10.10 icmp_seq=2 ttl=62 time=42.030 ms
84 bytes from 192.168.10.10 icmp_seq=3 ttl=62 time=39.927 ms
84 bytes from 192.168.10.10 icmp_seq=4 ttl=62 time=34.038 ms
84 bytes from 192.168.10.10 icmp_seq=5 ttl=62 time=40.854 ms

    好像也可以哦，没问题；若是不小心ping了一个不存在的地址呢？

    PC1> ping 192.168.40.10
*192.168.30.2 icmp_seq=1 ttl=254 time=698.062 ms (ICMP type:11, code:0, TTL expired in transit)
*192.168.30.2 icmp_seq=2 ttl=254 time=705.060 ms (ICMP type:11, code:0, TTL expired in transit)
*192.168.30.2 icmp_seq=3 ttl=254 time=707.124 ms (ICMP type:11, code:0, TTL expired in transit)
*192.168.30.2 icmp_seq=4 ttl=254 time=702.108 ms (ICMP type:11, code:0, TTL expired in transit)
*192.168.30.2 icmp_seq=5 ttl=254 time=694.003 ms (ICMP type:11, code:0, TTL expired in transit)

    PC2> ping 192.168.40.10
*192.168.30.1 icmp_seq=1 ttl=254 time=700.994 ms (ICMP type:11, code:0, TTL expired in transit)
*192.168.30.1 icmp_seq=2 ttl=254 time=704.114 ms (ICMP type:11, code:0, TTL expired in transit)
*192.168.30.1 icmp_seq=3 ttl=254 time=698.020 ms (ICMP type:11, code:0, TTL expired in transit)
*192.168.30.1 icmp_seq=4 ttl=254 time=700.092 ms (ICMP type:11, code:0, TTL expired in transit)
*192.168.30.1 icmp_seq=5 ttl=254 time=694.289 ms (ICMP type:11, code:0, TTL expired in transit)

    发现个问题，TTL传输中过期，说明数据包在两个路由器之间被互相转发，直到数据包TTL为0，这样势必会浪费路由器的资源，对正常的运作产生影响，所以这是不可行的。

    最后

    关于静态路由的相关实验到此结束，下一篇关于VLAN的实验。
  • 相关阅读:
    windows下Yarn安装与使用（两种方法）
    git配置公钥---解决码云出现git@gitee.com: Permission denied (publickey)
    npm使用国内镜像的两种方法
    【LeetCode】33. Search in Rotated Sorted Array (4 solutions)
    【LeetCode】83. Remove Duplicates from Sorted List
    【LeetCode】82. Remove Duplicates from Sorted List II
    【LeetCode】85. Maximal Rectangle
    【LeetCode】84. Largest Rectangle in Histogram
    【LeetCode】87. Scramble String
    【LeetCode】162. Find Peak Element (3 solutions)
  • 原文地址：https://www.cnblogs.com/llife/p/11328626.html
Copyright © 2011-2022 走看看