网卡绑定就是多张网卡逻辑上作为一张网卡用。可分为，负载均衡绑定和冗余绑定两种。
1.编辑虚拟网络接口配置文件
[root@test~]# more /etc/sysconfig/network-scripts/ifcfg-bond0
DEVICE=bond0
IPADDR=172.16.4.100
NETMASK=255.255.255.0
BROADCAST=172.16.4.255
NETWORK=172.168.4.100
ONBOOT=yes
2.编辑各网卡的配置文件，注意编辑之前做好备份工作
[root@test~]# more /etc/sysconfig/network-scripts/ifcfg-eth0
BOOTPROTO=none
TYPE=Ethernet
DEVICE=eth0
ONBOOT=yes
MASTER=bond0
slave=yes
[root@test ~]# more /etc/sysconfig/network-scripts/ifcfg-eth1
BOOTPROTO=none
TYPE=Ethernet
DEVICE=eth1
ONBOOT=yes
MASTER=bond0
slave=yes
3.改动/etc/modprobe.conf 文件，相同做好备份，最后增加2行
alias bond0 bonding
options bond0 miimon=100 mode=1
注：
（1）、miimon 是链路监測的时间间隔单位是毫秒，miimon=100的意思就是，每100毫秒检測网卡和交换机之间是否连通，如不通则使用另外的链路。
（2)、mode=0 表示负载均衡方式，两块网卡都工作，须要交换机作支持
mode=1 表示冗余方式，网卡仅仅有一个工作，一个出问题启用另外的
mode=6 表示负载均衡方式，两块网卡都工作，不须要交换机作支持
[root@test~]# more /etc/modprobe.conf
alias eth0 b44
alias eth1 8139too
alias usb-controller ehci-hcd
alias usb-controller1 ohci-hcd
alias bond0 bonding
options bond0 miimon=100 mode=0
4.在/etc/rc.d/rc.local 增加例如以下一行
ifenslave bond0 eth0 eth1
[root@test~]# more /etc/rc.d/rc.local
#!/bin/sh
#
# This script will be executed *after* all the other init scripts.
# You can put your own initialization stuff in here if you don't
# want to do the full Sys V style init stuff.
touch /var/lock/subsys/local
ifenslave bond0 eth0 eth1
5.又一次启动后负载平衡已经能正常工作，service network restart，
6.查看bond0的工作状态
[root@test~]# more /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v2.6.1 (October 29, 2004)
Bonding Mode: load balancing (round-robin)
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
Slave Interface: eth0
MII Status: up
Link Failure Count: 1
Permanent HW addr: 00:1b:b9:58:8b:b2
Slave Interface: eth1
MII Status: down
Link Failure Count: 0
Permanent HW addr: 00:07:40:6c:ac:c8
7.查看经过绑定后的网卡工作情况
[root@test ~]# ifconfig -a
bond0 Link encap:Ethernet HWaddr00:1B:B9:58:8B:B2
inet addr:172.16.4.100 Bcast:172.16.4.255 Mask:255.255.255.0
inet6 addr:fe80::200:ff:fe00:0/64 Scope:Link
UP BROADCAST RUNNINGMASTER MULTICAST MTU:1500 Metric:1
RX packets:744154errors:0 dropped:0 overruns:0 frame:0
TX packets:1866915errors:0 dropped:0 overruns:0 carrier:0
collisions:0txqueuelen:0
RX bytes:1099876146 (1.0GiB) TX bytes:121233595 (115.6 MiB)
eth0 Link encap:Ethernet HWaddr00:1B:B9:58:8B:B2
inet6 addr:fe80::21b:b9ff:fe58:8bb2/64 Scope:Link
UP BROADCAST RUNNINGSLAVE MULTICAST MTU:1500 Metric:1
RX packets:744154errors:0 dropped:0 overruns:0 frame:0
TX packets:1866905errors:0 dropped:0 overruns:0 carrier:0
collisions:0txqueuelen:1000
RX bytes:1099876146 (1.0GiB) TX bytes:121232839 (115.6 MiB)
Interrupt:9
eth1 Link encap:Ethernet HWaddr00:1B:B9:58:8B:B2
inet6 addr:fe80::21b:b9ff:fe58:8bb2/64 Scope:Link
UP BROADCAST SLAVEMULTICAST MTU:1500 Metric:1
RX packets:0 errors:0dropped:0 overruns:0 frame:0
TX packets:10 errors:0dropped:0 overruns:0 carrier:0
collisions:0txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:756 (756.0 b)
Interrupt:11 Baseaddress:0x1000
lo Link encap:Local Loopback
inetaddr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128Scope:Host
UP LOOPBACKRUNNING MTU:16436 Metric:1
RX packets:2129 errors:0dropped:0 overruns:0 frame:0
TX packets:2129 errors:0dropped:0 overruns:0 carrier:0
collisions:0txqueuelen:0
RX bytes:1998893 (1.9MiB) TX bytes:1998893 (1.9 MiB)
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0dropped:0 overruns:0 frame:0
TX packets:0 errors:0dropped:0 overruns:0 carrier:0
collisions:0txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
附：
DEVICE=物理设备名
IPADDR=IP地址
NETMASK=掩码值
NETWORK=网络地址
BROADCAST=广播地址
GATEWAY=网关地址
ONBOOT=[yes|no]（引导时是否激活设备）
USERCTL=[yes|no]（非root用户能否够控制该设备）
BOOTPROTO=[none|static|bootp|dhcp]（引导时不使用协议|静态分配|BOOTP协议|DHCP协议）
HWADDR = 你的MAC地址