数据来源:http://archive.ics.uci.edu/ml/datasets/Combined+Cycle+Power+Plant
数据描述:
有四个输入特征,这些数据来自电厂,这四个特征和电量输入有关系,现在通过线性回归求它们之间关系的模型参数。
- 温度,Temperature (T) in the range 1.81°C and 37.11°C,
- 大气压,Ambient Pressure (AP) in the range 992.89-1033.30 milibar,
- 相对湿度,Relative Humidity (RH) in the range 25.56% to 100.16%
- 排气容积,Exhaust Vacuum (V) in teh range 25.36-81.56 cm Hg
- 输出电力百万瓦:Net hourly electrical energy output (EP) 420.26-495.76 MW
The averages are taken from various sensors located around the plant that record the ambient variables every second. The variables are given without normalization.
注意,这些数据没有归一化,由于四个特征大小差别很大,所以要进行归一化操作,具体操作参照http://www.cnblogs.com/mikewolf2002/p/7560748.html 3.4节。
总共数据9568条数据,我们选取前9000条数据为训练数据,放在train.txt,后面568条数据为验证数据,放在verify.txt
![](https://images.cnblogs.com/OutliningIndicators/ContractedBlock.gif)
clear all; close all; clc; data = load('train.txt'); x = data(:,1:4); %温度,大气压,湿度,排气容积 y = data(:,5); %输出电力 m = length(y); % 样本数目 x = [ones(m, 1), x]; % 输入特征增加一列,x0=1 meanx = mean(x);%求均值 sigmax = std(x);%求标准偏差 x(:,2) = (x(:,2)-meanx(2))./sigmax(2); x(:,3) = (x(:,3)-meanx(3))./sigmax(3); x(:,4) = (x(:,4)-meanx(4))./sigmax(4); x(:,5) = (x(:,5)-meanx(5))./sigmax(5); theta = zeros(size(x(1,:)))'; % 初始化theta MAX_ITR = 1500;%最大迭代数目 alpha = 0.1; %学习率 i = 0; while(i<MAX_ITR) grad = (1/m).*x' * ((x * theta) - y);%求出梯度 theta = theta - alpha .* grad;%更新theta if(i>2) delta = old_theta-theta; delta_v = delta.*delta; if(delta_v<0.000000000000001)%如果两次theta的内积变化很小,退出迭代 break; end end old_theta = theta; %theta i=i+1; end data1 = load('verify.txt'); x1 = data1(:,1:4); %温度,压力,适度,压强 y1 = data1(:,5); %输出电力 m1 = length(y1); % 样本数目 x1 = [ones(m1, 1), x1]; % 输入特征增加一列,x0=1 meanx1 = mean(x1);%求均值 sigmax1 = std(x1);%求标准偏差 x1(:,2) = (x1(:,2)-meanx1(2))./sigmax1(2); x1(:,3) = (x1(:,3)-meanx1(3))./sigmax1(3); x1(:,4) = (x1(:,4)-meanx1(4))./sigmax1(4); x1(:,5) = (x1(:,5)-meanx1(5))./sigmax1(5); y2 = x1*theta; y2
y1为原始验证数据结果,y2为预测结果,从下面图中看到y1/y2都挺接近的。