智能家居esp8266对接机智云

依然存在稳定性问题

机智云官网——机智云

一个比较详细的教程——esp8266

一开始采用的是esp12f   可是他太不稳定，总是掉线，机智云的固件我也是刷了无数遍，哎太难了。

我比较懒，走过了太多的弯路。太迷茫又太累。博客很少写教程，只是做个笔记记述一下心路历程。

/**
************************************************************
***********************************************************/
#include <Gizwits.h>
#include <Wire.h>
#include <SoftwareSerial.h>
//#include <PinChangeInt.h>    //外部中断
SoftwareSerial mySerial(A2, A3); // A2 -> RX, A3 -> TX
bool varR_open = 0;
Gizwits myGizwits;
#define   KEY1              6
#define   KEY2              7
#define   KEY1_SHORT_PRESS  1
#define   KEY1_LONG_PRESS   2
#define   KEY2_SHORT_PRESS  4
#define   KEY2_LONG_PRESS   8
#define   NO_KEY            0
#define   KEY_LONG_TIMER    3
const int TrigPin = 10; 
const int EchoPin = 13; 
float cm; 
unsigned long Last_KeyTime = 0;
unsigned long gokit_time_s(void)
{
  return millis() / 1000;
}
char gokit_key1down(void)
{
  unsigned long keep_time = 0;
  if (digitalRead(KEY1) == LOW)
  {
    delay(100);
    if (digitalRead(KEY1) == LOW)
    {
      keep_time = gokit_time_s();
      while (digitalRead(KEY1) == LOW)
      {
        if ((gokit_time_s() - keep_time) > KEY_LONG_TIMER)
        {
          Last_KeyTime = gokit_time_s();
          return KEY1_LONG_PRESS;
        }
      } 
      if ((gokit_time_s() - Last_KeyTime) > KEY_LONG_TIMER)
      {
        return KEY1_SHORT_PRESS;
      }
      return 0;
    }
    return 0;
  }
  return 0;
}
char gokit_key2down(void)
{
  int unsigned long keep_time = 0;
  if (digitalRead(KEY2) == LOW)
  {
    delay(100);
    if (digitalRead(KEY2) == LOW)
    {
      keep_time = gokit_time_s();
      while (digitalRead(KEY2) == LOW) 
      {

        if ((gokit_time_s() - keep_time) > KEY_LONG_TIMER)
        {
          Last_KeyTime = gokit_time_s();
          return KEY2_LONG_PRESS;
        }
      }
      if ((gokit_time_s() - Last_KeyTime) > KEY_LONG_TIMER)
      {
        return KEY2_SHORT_PRESS;
      }
      return 0;
    }
    return 0;
  }
  return 0;
}
char gokit_keydown(void)
{
  char ret = 0;
  ret |= gokit_key2down();
  ret |= gokit_key1down();
  return ret;
}
/**
* KEY_Handle 
* @param none
* @return none
*/
void KEY_Handle(void)
{
  /*  Press for over than 3 second is Long Press  */
  switch (gokit_keydown())
  {
    case KEY1_SHORT_PRESS:
     // mySerial.println(F("KEY1_SHORT_PRESS , Production Test Mode "));
      myGizwits.setBindMode(WIFI_PRODUCTION_TEST);
      break;
    case KEY1_LONG_PRESS:
     // mySerial.println(F("KEY1_LONG_PRESS ,Wifi Reset"));
      myGizwits.setBindMode(WIFI_RESET_MODE);
      break;
    case KEY2_SHORT_PRESS:
     // mySerial.println(F("KEY2_SHORT_PRESS Soft AP mode"));
      myGizwits.setBindMode(WIFI_SOFTAP_MODE);
      //Soft AP mode
      break;
    case KEY2_LONG_PRESS:
     // mySerial.println(F("KEY2_LONG_PRESS ,AirLink mode"));
      myGizwits.setBindMode(WIFI_AIRLINK_MODE);
      digitalWrite(8,HIGH);
      //AirLink mode
      break;
    default:
      break;
  }
}
void ceju()
{
digitalWrite(TrigPin, LOW); 
delayMicroseconds(2); 
digitalWrite(TrigPin, HIGH); 
delayMicroseconds(10); 
digitalWrite(TrigPin, LOW); 
cm = pulseIn(EchoPin, HIGH) / 58.0; //算成厘米 
cm = (int(cm * 100.0)) / 100.0; //保留两位小数 
mySerial.println(cm);
//Serial.print(cm);
if(cm<20)
{
  digitalWrite(12,LOW);  
   digitalWrite(11,HIGH);
  } 
  
//Serial.print("cm"); 
//Serial.println();  
  }
/**
* Serial Init , Gizwits Init  
* @param none
* @return none
*/
void setup() {
  // put your setup code here, to run once:
  mySerial.begin(9600);
  pinMode(KEY1, INPUT_PULLUP);
  pinMode(KEY2, INPUT_PULLUP);
  pinMode(5,OUTPUT);//   led
  pinMode(8,OUTPUT);
  pinMode(9,INPUT);
  //pinMode (10,INPUT);
  
  pinMode(12,OUTPUT);
  pinMode (11,OUTPUT);
  digitalWrite(12,HIGH);  
  digitalWrite(11,HIGH);
  digitalWrite(5,HIGH);
  digitalWrite(9,HIGH);  
  digitalWrite(10,HIGH);
  pinMode(TrigPin, OUTPUT); 
pinMode(EchoPin, INPUT); 

  myGizwits.begin();
 // mySerial.println("GoKit init  OK 
");
  //attachPinChangeInterrupt(4,xianwei, CHANGE);  //开启外部中断
   //attachInterrupt(0,xianwei,FALLING);
}
void xianwei()
{
        digitalWrite(12,HIGH);  
        digitalWrite(11,LOW);
        delay(1000);
        digitalWrite(12,HIGH);  
        digitalWrite(11,HIGH);
  }
/**
* Wifi status printf  
* @param none
* @return none
*/
void wifiStatusHandle()
{
  if(myGizwits.wifiHasBeenSet(WIFI_SOFTAP))
  {
   // mySerial.println(F("WIFI_SOFTAP!"));
  }
  
  if(myGizwits.wifiHasBeenSet(WIFI_AIRLINK))
  {
   // mySerial.println(F("WIFI_AIRLINK!"));
  }
  
  if(myGizwits.wifiHasBeenSet(WIFI_STATION))
  {
   // mySerial.println(F("WIFI_STATION!"));
  }
  
  if(myGizwits.wifiHasBeenSet(WIFI_CON_ROUTER))
  {
    //mySerial.println(F("WIFI_CON_ROUTER!"));
  }
  
  if(myGizwits.wifiHasBeenSet(WIFI_DISCON_ROUTER))
  {
   // mySerial.println(F("WIFI_DISCON_ROUTER!"));
  }
  
  if(myGizwits.wifiHasBeenSet(WIFI_CON_M2M))
  {
   // mySerial.println(F("WIFI_CON_M2M!"));
  }
  
  if(myGizwits.wifiHasBeenSet(WIFI_DISCON_M2M))
  {
   // mySerial.println(F("WIFI_DISCON_M2M!"));
  }
}
/**
* Arduino loop 
* @param none
* @return none
*/
void loop() {  
  ceju();
    if(digitalRead(9)==LOW)
   {
    xianwei();
    }
   bool varR_open = 0;
  if(myGizwits.hasBeenSet(EVENT_open))
  {
    myGizwits.read(EVENT_open,&varR_open);
     if(varR_open ==1){
   digitalWrite(12,LOW);  
   digitalWrite(11,HIGH);
 
    }
    else
    {
    digitalWrite(12,HIGH);  
    digitalWrite(11,HIGH);
    }
  }
  bool varR_test = 0;
  if(myGizwits.hasBeenSet(EVENT_test))
  {
    myGizwits.read(EVENT_test,&varR_test);
     if(varR_test ==1){
    digitalWrite(5,LOW);
    }
    else
    {
       digitalWrite(5,HIGH);
    }
  }

  KEY_Handle();
  wifiStatusHandle();
  myGizwits.process();
}