dialogic d300 驱动重装后 dlstart 报错解决
问题描述：dlstart 后如下报错
[root@BJAPQ091 data]#dlstop
Stopping Dialogic Services...
Stopping Clocking Daemon:[ 纭�畾 ]
Stopping ClockingServer:[ 纭�畾 ]
Stopping Telephony System Monitor:[ 纭�畾 ]
Stopping Dialogic(R) board(s).
Deleting SW devices ....
Deleting SW devices Done
genload[17226]: Warning - Insufficient power overriden for the PCI Express board at bus 7, slot 0.
Stopping Timeslot Doler:[ 纭�畾 ]
Stopping Device Mapper:[ 纭�畾 ]
Shutting Down OAM Event Service:[ 纭�畾 ]
Stopping Dialogic Runtime Tracing Server:[ 纭�畾 ]
[root@BJAPQ091 ~]# dlstart
Starting Dialogic Services...
Starting Dialogic Runtime Tracing Server:[ 纭�畾 ]
Warning: You have chosen a Springware board to be the Primary clock master
Clock fallback will not be supported in this configuration
Starting OAM Event Service:[ 纭�畾 ]
Starting Device Mapper:[ 纭�畾 ]
Starting Timeslot Doler:[ 纭�畾 ]
Starting Telephony System Monitor:[ 纭�畾 ]
Starting Clocking Server:[ 纭�畾 ]
Starting Dialogic(R) board(s).
Dialogic(R) Generic Downloader Version 6.00 (Build 1)
Copyright (C) 1992-2007 Dialogic Corporation.
Using /usr/dialogic/cfg/dialogic.cfg to configure Dialogic Boards
genload[18399]: Warning - Insufficient power overriden for the PCI Express board at bus 7, slot 0.
System Download ........
Warning: Clock signals not detected on sec. lines
..............................................................................
D/300JCT-E1 (PCI ID 0) Download .. spisctr4 Firmware Version 6.70 Build 0024
1 Dialogic?Board Successfully Installed
Dialogic(R) SCSA Transmit Timeslot Assignment Program
Copyright (c) 1997-2007 Dialogic Corporation. All rights reserved
sctsassign:The Start TS is: 0 and Total Number of TS: 60
dxxxB1 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB2 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB3 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB4 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB5 : Failed open in sctsdtdxag.c: No such file or directory
dtiB1 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB6 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB7 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB8 : Failed open in sctsdtdxag.c: No such file or directory
Add SW Devices ....
REGVOX: #
REGVOX: # Dialogic Generic Configuration File
REGVOX: #
REGVOX: #
REGVOX: # Total number of virtual boards - 9
REGVOX: #
REGVOX:
REGVOX: #
REGVOX: # Board Type - D/300JCT-E1
REGVOX: #
REGVOX: dxxxB1 4 7000010 C FBFE0000 2000 20 SPAN 50004
REGVOX: dxxxB2 4 7000010 C FBFE2000 2000 20 SPAN 50005
REGVOX: dxxxB3 4 7000010 C FBFE4000 2000 20 SPAN 50006
REGVOX: dxxxB4 4 7000010 C FBFE6000 2000 20 SPAN 50007
REGVOX: dxxxB5 4 7000010 C FBFE0000 2000 0 SPAN 50008
REGVOX: dtiB1 30 7000010 T FBFE0000 2000 0 E1SPAN 50009
REGVOX: dxxxB6 4 7000010 C FBFE2000 2000 0 SPAN 50010
REGVOX: dxxxB7 4 7000010 C FBFE4000 2000 0 SPAN 50011
REGVOX: dxxxB8 2 7000010 C FBFE6000 2000 0 SPAN 50012
Add SW Devices Done
Checking for unsupported Dialogic boards:
usbu[18448]: Warning - Insufficient power overriden for the PCI Express board at bus 7, slot 0.
Starting Clocking Daemon:[ 纭�畾 ]
Starting fault detection on all Dialogic boards:[ 纭�畾 ]
解决办法：
经过google，发现是因为语音卡驱动加载openib与streams有冲突
（1）关闭应用 epos用户下 grMain -t
（2）root检查是否有安装openib rpm -qa | grep openib
（3）如果有，卸载openib rpm -e openib
（4）检查是否卸载成功 rpm -qa | grep openib
（5）重启机器
（6）root用户下 dlstop
（7）root下 dlstart 查看是否启动成功
（8）epos下 grMain -s -l5 -d5 -w -r 启动应用
参考文档：
Thought I would share this. I recently ran into this issue when trying to start Dialogic on RHEL 4. dlstart would produce the following. Apparently version 6 and older of up2date will load an openib package which conflicts with streams.
SCREEN OUTPUT:
dxxxB1 : Failed open in sctsdtdxag.c: No such file or directory
dtiB1 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB2 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB3 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB4 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB5 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB6 : Failed open in sctsdtdxag.c: No such file or directory
RTF LOG:
#Timestamp #PID #TID #Module #Client #Label #Message
06/23/2009 09:20:55.754 20988 3008342944 OAMSYSLOG ErrorEx DLGTIMESLOTDOLER - Fail to get TDMbus Attr error = 100
06/23/2009 09:20:55.755 20988 3008342944 OAMSYSLOG ErrorEx DLGTIMESLOTDOLER - Fail to get TDMbus Attr error = 100
06/23/2009 09:20:55.755 20988 3008342944 OAMSYSLOG ErrorEx DLGTIMESLOTDOLER - Fail to get TDMbus Attr error = 100
06/23/2009 09:20:56.249 21260 3086215392 spwrvoice ERR1 dxmain dxxxB1 ::::> dx_open() = -1, open(/dev/dlgn) = -1
06/23/2009 09:20:56.258 21260 3086215392 spwrvoice ERR1 dxmain dxxxB2 ::::> dx_open() = -1, open(/dev/dlgn) = -1
06/23/2009 09:20:56.259 21260 3086215392 spwrvoice ERR1 dxmain dxxxB3 ::::> dx_open() = -1, open(/dev/dlgn) = -1
06/23/2009 09:20:56.261 21260 3086215392 spwrvoice ERR1 dxmain dxxxB4 ::::> dx_open() = -1, open(/dev/dlgn) = -1
06/23/2009 09:20:56.262 21260 3086215392 spwrvoice ERR1 dxmain dxxxB5 ::::> dx_open() = -1, open(/dev/dlgn) = -1
06/23/2009 09:20:56.264 21260 3086215392 spwrvoice ERR1 dxmain dxxxB6 ::::> dx_open() = -1, open(/dev/dlgn) = -1
06/23/2009 09:20:57.375 21327 3086096896 OAMSYSLOG ErrorEx dlgclockdaemon - ConfigTDMBus(): Cannot retrieve TDM bus attributes from Device Mapper for bus id 158570088; 100 returned from dm_getAttributes().
06/23/2009 09:20:57.375 21327 3086096896 OAMSYSLOG ErrorEx dlgclockdaemon - ConfigTDMBus(): FATAL CONFIGURATION ERROR.
06/23/2009 09:20:57.375 21327 3086096896 OAMSYSLOG ErrorEx dlgclockdaemon - Failed to configure the TDM bus; ConfigTDMBus() returned 0x0.
06/23/2009 09:20:58.956 21352 3061984160 OAMIPC Warning OAMTransport - CSocketClientTransport::SendMessage() - m_ClientReceiveSocket.ShutAndCloseSocket failed
06/23/2009 09:20:58.955 21051 2892954528 OAMSYSLOG ErrorEx DLGSPWRFAULTDETECTOR - CNIStatus::init(): Failed to open the DTI device dtiB1
FIND AND FIX:
[root@ares cfg]# lsmod
Module Size Used by
mercd 281204 0
ctimod 28916 1 mercd
streams_dvbmDriver 132616 0
streams_sctmrDriver 29104 0
streams_gpioDriver 21028 0
streams_gncfdDriver 19112 0
streams_dlgnDriver 418536 4 streams_dvbmDriver,streams_sctmrDriver,streams_gpioDriver,streams_gncfdDriver
streams 859756 5 streams_dvbmDriver,streams_sctmrDriver,streams_gpioDriver,streams_gncfdDriver,streams_dlgnDriver
parport_pc 28033 0
lp 15661 0
parport 38153 2 parport_pc,lp
autofs4 26053 0
i2c_dev 14529 0
i2c_core 26305 1 i2c_dev
sunrpc 145061 1
ipt_REJECT 10689 1
ipt_state 5953 17
ip_conntrack 46085 1 ipt_state
iptable_filter 6977 1
ip_tables 23105 3 ipt_REJECT,ipt_state,iptable_filter
cpufreq_powersave 5953 0
ib_srp 39005 0
ib_sdp 61437 0
ib_ipoib 81769 0
inet_lro 13121 1 ib_ipoib
md5 8129 1
ipv6 244833 84 ib_ipoib
rdma_ucm 21189 0
rdma_cm 39937 2 ib_sdp,rdma_ucm
iw_cm 13381 1 rdma_cm
ib_addr 12357 1 rdma_cm
ib_umad 21737 0
ib_ucm 22213 0
ib_uverbs 41833 2 rdma_ucm,ib_ucm
ib_cm 46521 4 ib_srp,ib_ipoib,rdma_cm,ib_ucm
ib_sa 43213 4 ib_srp,ib_ipoib,rdma_cm,ib_cm
ib_mad 39897 3 ib_umad,ib_cm,ib_sa
ib_core 66369 12 ib_srp,ib_sdp,ib_ipoib,rdma_ucm,rdma_cm,iw_cm,ib_umad,ib_ucm,ib_uverbs,ib_cm,ib_sa,ib_mad
button 10705 0
battery 12997 0
ac 8901 0
uhci_hcd 33241 0
e100 36677 0
mii 9281 1 e100
e1000 122837 0
floppy 58193 0
dm_snapshot 22633 0
dm_zero 6337 0
dm_mirror 32969 0
ext3 119753 4
jbd 59865 1 ext3
dm_mod 67049 12 dm_snapshot,dm_zero,dm_mirror
ata_piix 19909 2
libata 105629 1 ata_piix
sd_mod 20801 3
scsi_mod 120525 3 ib_srp,libata,sd_mod
[root@ares cfg]# rpm -qa | grep openib
openib-1.4-1.el4
[root@ares cfg]# rpm -e openib
[root@ares cfg]# rpm -qa | grep openib
Then reboot and all is back to normal. Hope this helps some one else out there.
北京行二号机 dlstart 报错解决
问题描述：dlstart 后如下报错
[root@BJAPQ091 data]#dlstop
Stopping Dialogic Services...
Stopping Clocking Daemon:[ 纭�畾 ]
Stopping ClockingServer:[ 纭�畾 ]
Stopping Telephony System Monitor:[ 纭�畾 ]
Stopping Dialogic(R) board(s).
Deleting SW devices ....
Deleting SW devices Done
genload[17226]: Warning - Insufficient power overriden for the PCI Express board at bus 7, slot 0.
Stopping Timeslot Doler:[ 纭�畾 ]
Stopping Device Mapper:[ 纭�畾 ]
Shutting Down OAM Event Service:[ 纭�畾 ]
Stopping Dialogic Runtime Tracing Server:[ 纭�畾 ]
[root@BJAPQ091 ~]# dlstart
Starting Dialogic Services...
Starting Dialogic Runtime Tracing Server:[ 纭�畾 ]
Warning: You have chosen a Springware board to be the Primary clock master
Clock fallback will not be supported in this configuration
Starting OAM Event Service:[ 纭�畾 ]
Starting Device Mapper:[ 纭�畾 ]
Starting Timeslot Doler:[ 纭�畾 ]
Starting Telephony System Monitor:[ 纭�畾 ]
Starting Clocking Server:[ 纭�畾 ]
Starting Dialogic(R) board(s).
Dialogic(R) Generic Downloader Version 6.00 (Build 1)
Copyright (C) 1992-2007 Dialogic Corporation.
Using /usr/dialogic/cfg/dialogic.cfg to configure Dialogic Boards
genload[18399]: Warning - Insufficient power overriden for the PCI Express board at bus 7, slot 0.
System Download ........
Warning: Clock signals not detected on sec. lines
..............................................................................
D/300JCT-E1 (PCI ID 0) Download .. spisctr4 Firmware Version 6.70 Build 0024
1 Dialogic?Board Successfully Installed
Dialogic(R) SCSA Transmit Timeslot Assignment Program
Copyright (c) 1997-2007 Dialogic Corporation. All rights reserved
sctsassign:The Start TS is: 0 and Total Number of TS: 60
dxxxB1 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB2 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB3 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB4 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB5 : Failed open in sctsdtdxag.c: No such file or directory
dtiB1 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB6 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB7 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB8 : Failed open in sctsdtdxag.c: No such file or directory
Add SW Devices ....
REGVOX: #
REGVOX: # Dialogic Generic Configuration File
REGVOX: #
REGVOX: #
REGVOX: # Total number of virtual boards - 9
REGVOX: #
REGVOX:
REGVOX: #
REGVOX: # Board Type - D/300JCT-E1
REGVOX: #
REGVOX: dxxxB1 4 7000010 C FBFE0000 2000 20 SPAN 50004
REGVOX: dxxxB2 4 7000010 C FBFE2000 2000 20 SPAN 50005
REGVOX: dxxxB3 4 7000010 C FBFE4000 2000 20 SPAN 50006
REGVOX: dxxxB4 4 7000010 C FBFE6000 2000 20 SPAN 50007
REGVOX: dxxxB5 4 7000010 C FBFE0000 2000 0 SPAN 50008
REGVOX: dtiB1 30 7000010 T FBFE0000 2000 0 E1SPAN 50009
REGVOX: dxxxB6 4 7000010 C FBFE2000 2000 0 SPAN 50010
REGVOX: dxxxB7 4 7000010 C FBFE4000 2000 0 SPAN 50011
REGVOX: dxxxB8 2 7000010 C FBFE6000 2000 0 SPAN 50012
Add SW Devices Done
Checking for unsupported Dialogic boards:
usbu[18448]: Warning - Insufficient power overriden for the PCI Express board at bus 7, slot 0.
Starting Clocking Daemon:[ 纭�畾 ]
Starting fault detection on all Dialogic boards:[ 纭�畾 ]
解决办法：
经过google，发现是因为语音卡驱动加载openib与streams有冲突
（1）关闭应用 epos用户下 grMain -t
（2）root检查是否有安装openib rpm -qa | grep openib
（3）如果有，卸载openib rpm -e openib
（4）检查是否卸载成功 rpm -qa | grep openib
（5）重启机器
（6）root用户下 dlstop
（7）root下 dlstart 查看是否启动成功
（8）epos下 grMain -s -l5 -d5 -w -r 启动应用
感谢这位国外的和我一样的倒霉蛋。
参考文档：
Thought I would share this. I recently ran into this issue when trying to start Dialogic on RHEL 4. dlstart would produce the following. Apparently version 6 and older of up2date will load an openib package which conflicts with streams.
SCREEN OUTPUT:
dxxxB1 : Failed open in sctsdtdxag.c: No such file or directory
dtiB1 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB2 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB3 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB4 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB5 : Failed open in sctsdtdxag.c: No such file or directory
dxxxB6 : Failed open in sctsdtdxag.c: No such file or directory
RTF LOG:
#Timestamp #PID #TID #Module #Client #Label #Message
06/23/2009 09:20:55.754 20988 3008342944 OAMSYSLOG ErrorEx DLGTIMESLOTDOLER - Fail to get TDMbus Attr error = 100
06/23/2009 09:20:55.755 20988 3008342944 OAMSYSLOG ErrorEx DLGTIMESLOTDOLER - Fail to get TDMbus Attr error = 100
06/23/2009 09:20:55.755 20988 3008342944 OAMSYSLOG ErrorEx DLGTIMESLOTDOLER - Fail to get TDMbus Attr error = 100
06/23/2009 09:20:56.249 21260 3086215392 spwrvoice ERR1 dxmain dxxxB1 ::::> dx_open() = -1, open(/dev/dlgn) = -1
06/23/2009 09:20:56.258 21260 3086215392 spwrvoice ERR1 dxmain dxxxB2 ::::> dx_open() = -1, open(/dev/dlgn) = -1
06/23/2009 09:20:56.259 21260 3086215392 spwrvoice ERR1 dxmain dxxxB3 ::::> dx_open() = -1, open(/dev/dlgn) = -1
06/23/2009 09:20:56.261 21260 3086215392 spwrvoice ERR1 dxmain dxxxB4 ::::> dx_open() = -1, open(/dev/dlgn) = -1
06/23/2009 09:20:56.262 21260 3086215392 spwrvoice ERR1 dxmain dxxxB5 ::::> dx_open() = -1, open(/dev/dlgn) = -1
06/23/2009 09:20:56.264 21260 3086215392 spwrvoice ERR1 dxmain dxxxB6 ::::> dx_open() = -1, open(/dev/dlgn) = -1
06/23/2009 09:20:57.375 21327 3086096896 OAMSYSLOG ErrorEx dlgclockdaemon - ConfigTDMBus(): Cannot retrieve TDM bus attributes from Device Mapper for bus id 158570088; 100 returned from dm_getAttributes().
06/23/2009 09:20:57.375 21327 3086096896 OAMSYSLOG ErrorEx dlgclockdaemon - ConfigTDMBus(): FATAL CONFIGURATION ERROR.
06/23/2009 09:20:57.375 21327 3086096896 OAMSYSLOG ErrorEx dlgclockdaemon - Failed to configure the TDM bus; ConfigTDMBus() returned 0x0.
06/23/2009 09:20:58.956 21352 3061984160 OAMIPC Warning OAMTransport - CSocketClientTransport::SendMessage() - m_ClientReceiveSocket.ShutAndCloseSocket failed
06/23/2009 09:20:58.955 21051 2892954528 OAMSYSLOG ErrorEx DLGSPWRFAULTDETECTOR - CNIStatus::init(): Failed to open the DTI device dtiB1
FIND AND FIX:
[root@ares cfg]# lsmod
Module Size Used by
mercd 281204 0
ctimod 28916 1 mercd
streams_dvbmDriver 132616 0
streams_sctmrDriver 29104 0
streams_gpioDriver 21028 0
streams_gncfdDriver 19112 0
streams_dlgnDriver 418536 4 streams_dvbmDriver,streams_sctmrDriver,streams_gpioDriver,streams_gncfdDriver
streams 859756 5 streams_dvbmDriver,streams_sctmrDriver,streams_gpioDriver,streams_gncfdDriver,streams_dlgnDriver
parport_pc 28033 0
lp 15661 0
parport 38153 2 parport_pc,lp
autofs4 26053 0
i2c_dev 14529 0
i2c_core 26305 1 i2c_dev
sunrpc 145061 1
ipt_REJECT 10689 1
ipt_state 5953 17
ip_conntrack 46085 1 ipt_state
iptable_filter 6977 1
ip_tables 23105 3 ipt_REJECT,ipt_state,iptable_filter
cpufreq_powersave 5953 0
ib_srp 39005 0
ib_sdp 61437 0
ib_ipoib 81769 0
inet_lro 13121 1 ib_ipoib
md5 8129 1
ipv6 244833 84 ib_ipoib
rdma_ucm 21189 0
rdma_cm 39937 2 ib_sdp,rdma_ucm
iw_cm 13381 1 rdma_cm
ib_addr 12357 1 rdma_cm
ib_umad 21737 0
ib_ucm 22213 0
ib_uverbs 41833 2 rdma_ucm,ib_ucm
ib_cm 46521 4 ib_srp,ib_ipoib,rdma_cm,ib_ucm
ib_sa 43213 4 ib_srp,ib_ipoib,rdma_cm,ib_cm
ib_mad 39897 3 ib_umad,ib_cm,ib_sa
ib_core 66369 12 ib_srp,ib_sdp,ib_ipoib,rdma_ucm,rdma_cm,iw_cm,ib_umad,ib_ucm,ib_uverbs,ib_cm,ib_sa,ib_mad
button 10705 0
battery 12997 0
ac 8901 0
uhci_hcd 33241 0
e100 36677 0
mii 9281 1 e100
e1000 122837 0
floppy 58193 0
dm_snapshot 22633 0
dm_zero 6337 0
dm_mirror 32969 0
ext3 119753 4
jbd 59865 1 ext3
dm_mod 67049 12 dm_snapshot,dm_zero,dm_mirror
ata_piix 19909 2
libata 105629 1 ata_piix
sd_mod 20801 3
scsi_mod 120525 3 ib_srp,libata,sd_mod
[root@ares cfg]# rpm -qa | grep openib
openib-1.4-1.el4
[root@ares cfg]# rpm -e openib
[root@ares cfg]# rpm -qa | grep openib
Then reboot and all is back to normal. Hope this helps some one else out there.