windows raid mode重新安装系统（win10）

常规安装模式：

STEP 1 进入bios 将高级设置中，引导模式设置为传统（旧模式）模式,一般存在legacy (旧模式)，uefi with csm ,uefi without csm 三个模式，选择legacy 或旧模式。

STEP 2 在高级设置里，将设备设置里的设备模式设置成RAID ，并且 将CTRL+I 选项打开。 保存重启系统

STEP 3 开机时同时按ctrl +I 进入 raid 设置界面。

STEP 4 进入raid 设置界面之后，可以看到SSD 出于cache 状态。选择reset disk to non-raid，按空格选中ssd，按enter 清楚cache 状态，点Y 确认，然后R 移除加速磁盘。此时可以看到两块磁盘都是NON-RAID DISK 状态。

STEP 5 按ESC 退出

STEP 6 常规安装windows 10. 在选择安装系统分区的时候，点击加载驱动程序（此驱动程序需要预先放到USB U盘中），选择RAID 驱动程序f6flpy-x64。 驱动安装完成后，进入windows 常规安装流程。注意，安装盘不要原则RAID 加速的SSD。

STEP 7 安装完成后，将引导模式设置为 UEFI 中的一个即可。

 

 

 

常规安装模式失败的情况下（CTRL+I 失效）的安装模式。

 

STEP 1 将bios 里的引导模式设置为 LEGACY （旧模式），设备模式设置为AHCI ，SSD加速盘不能有分区。

STEP 2 正常安装windows 10

STEP 3 如果已安装intel rapid storage technology ，卸载intel rapid storage technology。

STEP 4 win键+R 运行 msconfig，然后 选择 boot tab -> check safe boot -> restart

STEP 5 进入BIOS 将设备模式改为 RAID 引导模式改为 UEFI 保存退出

STEP 6 WINDOWS 会自动进入安全模式。

STEP 7 win键+R 运行 msconfig，然后 选择 general tab ->normal startup circle(正常启动)--> restart

STEP 8 进入正常模式进入windows 安装 intel raid 驱动。(setupRST.exe).  然后重启

SETP 9 进入winodows 打开 intel RST 配置工具（装完SETUPRST 之后就有了），点击performance -> enable accelerate -> ok.  完成。

 

 

 

 

 

 

 

 

How to: Change SATA Modes After Windows Installation

Types of SATA modes:

• IDE - Old, slower, it is simply a compatibility mode
• AHCI - AHCI stands for Advanced Host Controller Interface. It makes Native Command Queuing (NCQ) along with hot-plugging or hot swapping through SATA Serial-ATA host controllers possible. NCQ is one of the important features of AHCI for SSDs. SSDs can process requests faster than HDDs. It can process so fast that the SSD could end up waiting for work. NCQ allows the OS/controller to request up to 32 simultaneous requests at once. So you basically get more performance from your drive over older IDE mode.
• RAID - RAID stands for redundant array of independent disks, originally redundant array of inexpensive disks. It is a means by which your PC uses multiple disks as if they were one, either to increase performance, safeguard against disk failures, or both. RAID mode has all the advantages of AHCI mode. There are four main factors of a RAID setup: striping, which spreads data across multiple drives, mirroring, which copies the data to more than one disk, space efficiency, which is how much of the total space is available to use, and fault tolerance, which is a measure of how well protected the RAID array is against disk failure.

The Problem:
The issue with changing the SATA modes is they need to be enabled in the BIOS prior to OS installation; doing so after you have installed the OS will disable the PC. The reason why is Windows disables the drivers for the others that are not needed during installation. This tutorial will show you how to enable the different SATA modes after you have installed the OS.

Notes:
*You may need to install the IRST driver first in order to do the registry change from AHCI mode to RAID mode for Intel mobos.
*You may have to uninstall then reinstall any SATA drivers such as Intel RST or AMDs equivalent.


Windows 7

Change to AHCI mode from IDE mode:Warning: Spoiler! (Click to hide)

You can use the MS Fix it tool or edit the registry yourself.

Link to tool here: (link)

Regedit:

1. Exit all Windows-based programs.
2. Press [Win] + R or take the RUN option from the start menu.
3. Now type Regedit there and press Enter Key to open up the Registry Editor Window. (If you receive the User Account Control dialog box, click Continue.)
4. Locate and then click the following registry sub key:
   Code:

   HKEY_LOCAL_MACHINESystemCurrentControlSetServicesmsahci

5. In the right pane right-click Start in the Name column and then click Modify.
6. In the Value data box, type 0 [3 is default], and then click OK.
7. On the File menu, click Exit to close Registry Editor.
8. Restart your computer
9. Go to UEFI/BIOS and enable AHCI, Save & Reboot
10. Another restart will be required to finish the driver installation.

Change to ACHI mode from RAID mode:Warning: Spoiler! (Click to hide)

1. Exit all Windows-based programs.
2. Press [Win] + R or take the RUN option from the start menu.
3. Now type regedit there and press Enter Key to open up the Registry Editor Window.
4. If you receive the User Account Control dialog box, click Continue.
5. Locate and then click the following registry subkeys:
   Code:

   HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicespciide
   HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesmsahci
   HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesiaStorV
   HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesiaStor
   HKEY_LOCAL_MACHINESystemCurrentControlSetServicesatapi

6. In the right pane, right-click Start in the Name column, and then click Modify.
7. In the Value data box, type 0 [3 is default], and then click OK.
8. On the File menu, click Exit to close Registry Editor.
9. Restart your computer
10. Go to UEFI/BIOS and enable AHCI, Save & Reboot
11. Another restart will be required to finish the driver installation.
    Note: You might not have the last registry key (iastor) as this is installed in the registry with the intel raid drivers, the default windows 7 raid driver uses the iastorV key.

Change to RAID mode from AHCI mode or IDE mode:Warning: Spoiler! (Click to hide)

1. Exit all Windows-based programs.
2. Press [Win] + R or take the RUN option from the start menu.
3. Now type regedit there and press Enter Key to open up the Registry Editor Window.
4. If you receive the User Account Control dialog box, click Continue.
5. Locate and then click the following registry subkeys:
   Code:

   HKEY_LOCAL_MACHINESystemCurrentControlSetServicesmsahci
   HKEY_LOCAL_MACHINESystemCurrentControlSetServicesiaStorV
   HKEY_LOCAL_MACHINESystemCurrentControlSetServicesiaStor

6. In the right pane, right-click Start in the Name column, and then click Modify.
7. In the Value data box, type 0 [3 is default], and then click OK.
8. On the File menu, click Exit to close Registry Editor.
9. Restart your computer
10. Go to UEFI/BIOS and enable RAID, Save & Reboot
11. Another restart will be required to finish the driver installation.
    Note: If you have an AMD systems you may need to look here too:http://superuser.com/questions/300035/how-to-install-amd-raid-driver-after-windows-installation

Change to IDE mode from AHCI or RAID mode:Warning: Spoiler! (Click to hide)

1. Exit all Windows-based programs.
2. Press [Win] + R or take the RUN option from the start menu.
3. Now type regedit there and press Enter Key to open up the Registry Editor Window.
4. If you receive the User Account Control dialog box, click Continue.
5. Locate and then click the following registry subkey:
   Code:

   HKEY_LOCAL_MACHINESystemCurrentControlSetServicesPciide

6. In the right pane, right-click Start in the Name column, and then click Modify.
7. In the Value data box, type 0 [3 is default], and then click OK.
8. On the File menu, click Exit to close Registry Editor.
9. Restart your computer
10. Go to UEFI/BIOS and enable IDE, Save & Reboot
11. Another restart will be required to finish the driver installation.

For those with nForce boards:Warning: Spoiler! (Click to hide)

Quote:

Just to put in here for nForce users, nForce boards do not support AHCI (with the exception of nForce boards that include onboard graphic cards), and also don't send the TRIM command for SSDs. It can do NCQ through its controller though. The JMicron SATA ports do support AHCI, but you'd get worse performance running a HDD through these, than on the normal SATA ports.

You can uninstall the Nvidia controller though in Device Manager and install Microsoft's IDE Controller, which can send TRIM commands for SSDs.

Head to Device Manager (Open Start menu, type Device Manager), and click "IDE ATA/ATAPI Controllers", and you will see 3 Nvidia Serial ATA Controllers. Right click one of them and click "Properties" and go to the "" tab. Click "Update ". Click "Browse my Computer", and then "Let me pick". You will see the option to choose "Standard Dual Channel PCI IDE Controller". Click this and click "Next" and let it install.

Do the same for the other two Nvidia Controllers in Device Manager and restart your system. After the controllers have installed, you will be asked to reboot again.

SSDs will now have a slight performance boost with the TRIM command, and also regular HDDs also have a slight increase as well.

Windows 8

Change to AHCI mode from IDE mode:Warning: Spoiler! (Click to hide)

Link to some other info here: (link)

Regedit:

1. Exit all Windows-based programs.
2. Press [Win] + R or take the RUN option from the start menu.
3. Now type Regedit there and press Enter Key to open up the Registry Editor Window. (If you receive the User Account Control dialog box, click Continue.)
4. Locate and then click the following registry sub keys:
   Code:

   HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesstorahci

5. Locate the Error Control entry which should have a value of 3. Right-click on the entry name, select Modify, change the value from 3 to 0 and click OK.
6. Locate and then click the following registry sub keys:
   Code:

   HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesstorahciStartOverride

7. Locate an entry named "0" with a value of 3. Change the value to 0 by following the procedure in step 5.
8. Restart your computer
9. Go to UEFI/BIOS and enable AHCI, Save & Reboot
10. Another restart may be required to finish the driver installation.

Change to RAID mode from AHCI mode and vice versa:Warning: Spoiler! (Click to hide)

1. If currently installed, uninstall your RAID or AHCI SATA driver (for intel, intel rapid storage technology)
2. Basically open msconfig -> boot tab -> check safe boot -> restart
3. Go into UEFI/BIOS and set SATA mode to which ever one you want
4. Boot up into windows safe mode
5. Open msconfig again -> under the main menu tab (general) click the normal startup circle - > restart
6. Your system should boot into windows fine and you can install your AHCI or RAID driver.
   
   来源： http://www.overclock.net/t/1227636/how-to-change-sata-modes-after-windows-installation

 

 

Windows 10

Change to AHCI mode from IDE mode:  未验证Warning: Spoiler! (Click to hide)

Link to some other info here: (link)

Regedit:

1. Exit all Windows-based programs.
2. Press [Win] + R or take the RUN option from the start menu.
3. Now type Regedit there and press Enter Key to open up the Registry Editor Window. (If you receive the User Account Control dialog box, click Continue.)
4. Locate and then click the following registry sub keys:
   Code:

   HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesstorahci

5. Locate the Error Control entry which should have a value of 3. Right-click on the entry name, select Modify, change the value from 3 to 0 and click OK.
6. Locate and then click the following registry sub keys:
   Code:

   HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesstorahciStartOverride

7. Locate an entry named "0" with a value of 3. Change the value to 0 by following the procedure in step 5.
8. Restart your computer
9. Go to UEFI/BIOS and enable AHCI, Save & Reboot
10. Another restart may be required to finish the driver installation.

Change to RAID mode from AHCI mode and vice versa: 以验证Warning: Spoiler! (Click to hide)

1. If currently installed, uninstall your RAID or AHCI SATA driver (for intel, intel rapid storage technology)
2. Basically open msconfig -> boot tab -> check safe boot -> restart
3. Go into UEFI/BIOS and set SATA mode to which ever one you want
4. Boot up into windows safe mode
5. Open msconfig again -> under the main menu tab (general) click the normal startup circle - > restart
6. Your system should boot into windows fine and you can install your AHCI or RAID driver.
   
   来源： http://www.overclock.net/t/1227636/how-to-change-sata-modes-after-windows-installation

 

Recreation of RAID, EliteBook 840（ win 7）

Options

 

‎03-27-2016 10:39 AM

Working reinstall procedure:

Step 1 reinstall OS:

- take the hdd and reinstall easily in a desktop computer (cdrom etc) in AHCI mode.

- re-insert in the laptop and run in AHCI mode

At this point you have 2 separate drives - sata hdd and ssd

Step 2 re-enable the SSD cache:

Change from AHCI to RAID:

Change to RAID mode from AHCI mode or IDE mode:Warning: Spoiler! (Click to hide)

1. Exit all Windows-based programs.
2. Press [Win] + R or take the RUN option from the start menu.
3. Now type regedit there and press Enter Key to open up the Registry Editor Window.
4. If you receive the User Account Control dialog box, click Continue.
5. Locate and then click the following registry subkeys:
   Code:

   HKEY_LOCAL_MACHINESystemCurrentControlSetServicesmsahci
   HKEY_LOCAL_MACHINESystemCurrentControlSetServicesiaStorV
   HKEY_LOCAL_MACHINESystemCurrentControlSetServicesiaStor

6. In the right pane, right-click Start in the Name column, and then click Modify.
7. In the Value data box, type 0 [3 is default], and then click OK.
8. On the File menu, click Exit to close Registry Editor.
9. Restart your computer
10. Go to UEFI/BIOS and enable RAID, Save & Reboot
11. Another restart will be required to finish the driver installation.

Source link:

http://www.overclock.net/t/1227636/how-to-change-sata-modes-after-windows-installation

After reboot in device manager AHCI controller is replaced by RAID controller.

Reinstall Intel RST driver.

Delete any existing partition on SSD.

Start RST GUI - now you have the option to create the RAID.