AP型号为DWL-2200AP，我们要在2层交换机的17口(192.168.22.1)加入这个AP，并分配AP的IP地址192.168.22.2。DHCP地址池从192.168.22.3～192.168.22.53。
为技术中心实验组添加无线ap的VLAN
cisco3560#conf t
Enter configuration commands, one per line. End with CNTL/Z.
cisco3560(config)#vlan 22
cisco3560(config-vlan)#name shiyanzu_wireless
cisco3560(config-vlan)#exit
cisco3560(config)#int vlan 22
cisco3560(config-if)#ip address 192.168.22.1 255.255.255.0
cisco3560(config-if)#end
cisco3560#wr
Building configuration...
[OK]
--===--------------------[将二层交换机的17口加入到vlan22]----------------------===---
cisco3560#192.168.0.6
Trying 192.168.0.6 ... Open
User Access Verification
Password:
backBuilding>en
Password:
backBuilding#show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/17, Fa0/18, Fa0/19, Fa0/20
Fa0/21, Fa0/22, Fa0/23, Fa0/24
Fa0/25, Fa0/26, Fa0/27, Fa0/28
Fa0/29, Fa0/30, Fa0/31, Fa0/32
Fa0/33, Fa0/34, Fa0/35, Fa0/36
Fa0/37, Fa0/38, Fa0/39, Fa0/40
Fa0/41, Fa0/42, Fa0/43, Fa0/44
Fa0/45, Fa0/46, Fa0/47, Fa0/48
Gi0/1, Gi0/2
2 zongjingbu active
3 caiwubu active
4 guojibu active
5 gongyingbu active
6 kaifabu active Fa0/13, Fa0/14, Fa0/15, Fa0/16
7 jishubu active
8 shichangbu active
9 zhiguanbu active
10 gongchengbu active
11 jihuabu active
12 shengchanbu active
13 zhuanjiazu active
14 zonggongban active
15 zongkuaiban active
17 wireless_sourth active
18 wl_zjb active
19 jihuabu_2 active Fa0/2, Fa0/3, Fa0/4
20 shengchanbu_2 active Fa0/5, Fa0/6, Fa0/7, Fa0/8
21 zhiguanbu_2 active Fa0/9, Fa0/10, Fa0/11, Fa0/12
22 shiyanzu_wireless active
100 HUB_CNC active
101 HUB_TEL active
1002 fddi-default act/unsup
1003 trcrf-default act/unsup
1004 fddinet-default act/unsup
1005 trbrf-default act/unsup
backBuilding#conf t
Enter configuration commands, one per line. End with CNTL/Z.
backBuilding(config)#int f0/17
backBuilding(config-if)#switch access vlan 22
backBuilding(config-if)#exit
backBuilding(config)#exit
backBuilding#show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/18, Fa0/19, Fa0/20, Fa0/21
Fa0/22, Fa0/23, Fa0/24, Fa0/25
Fa0/26, Fa0/27, Fa0/28, Fa0/29
Fa0/30, Fa0/31, Fa0/32, Fa0/33
Fa0/34, Fa0/35, Fa0/36, Fa0/37
Fa0/38, Fa0/39, Fa0/40, Fa0/41
Fa0/42, Fa0/43, Fa0/44, Fa0/45
Fa0/46, Fa0/47, Fa0/48, Gi0/1
Gi0/2
2 zongjingbu active
3 caiwubu active
4 guojibu active
5 gongyingbu active
6 kaifabu active Fa0/13, Fa0/14, Fa0/15, Fa0/16
7 jishubu active
8 shichangbu active
9 zhiguanbu active
10 gongchengbu active
11 jihuabu active
12 shengchanbu active
13 zhuanjiazu active
14 zonggongban active
15 zongkuaiban active
17 wireless_sourth active
18 wl_zjb active
19 jihuabu_2 active Fa0/2, Fa0/3, Fa0/4
20 shengchanbu_2 active Fa0/5, Fa0/6, Fa0/7, Fa0/8
21 zhiguanbu_2 active Fa0/9, Fa0/10, Fa0/11, Fa0/12
22 shiyanzu_wireless active Fa0/17
100 HUB_CNC active
101 HUB_TEL active
1002 fddi-default act/unsup
1003 trcrf-default act/unsup
1004 fddinet-default act/unsup
1005 trbrf-default act/unsup
backBuilding#
将计算机和AP用网线连接，默认AP的ip地址是192.168.0.50，因此设置计算机的IP地址为192.168.0.*即可，掩码24位，网关和dns不设置。
在ie地址栏内输入http://192.168.0.50/,默认用户名为admin，密码空，进入系统。
点击wireless按钮，设置channel为6，启用开放式系统加密，采用64bits的ascii方式，first key设置密码；启用super g mode。完成后应用重启。
选择Advanced->DHCP Server，启用DHCP功能，并配置dhcp池，完成后应用重启。
选择Home->LAN，设置好IP地址和网关，重启。
修改本机的IP地址和AP在同一网段，重新登录AP检查配置信息，支持本机多网卡不同网段，一切OK～！