Pset_MaterialWoodBasedPanel

Pset_MaterialWoodBasedPanel

材料人造板：这是一个有关人造板的机械性能，如胶合板或OSB板类产品的材料的集合。上述关于木基梁材料各向异性、根据构件尺寸（特别是面板厚度）的强度分级的命题也适用。

Name

Type

Description

ApplicableStructuralDesignMethod

P_SINGLEVALUE / IfcLabel

Applicable Structural Design Method

Determines whether mechanical material properties are applicable to 'ASD' = allowable stress design (working stress design), 'LSD' = limit state design, or 'LRFD' = load and resistance factor design.

InPlane

COMPLEX / CP_MaterialMechanicalPanel

In Plane

Mechanical properties with respect to in-plane load, i.e. for function as a membrane.

Name	Type	Description
YoungModulusBending	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcModulusOfElasticityMeasure	Defining values: α; defined values: elastic modulus in bending.
YoungModulusTension	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcModulusOfElasticityMeasure	Defining values: α; defined values: elastic modulus in tension.
YoungModulusCompression	P_SINGLEVALUE / IfcModulusOfElasticityMeasure	Elastic modulus in compression.
ShearModulus	P_SINGLEVALUE / IfcModulusOfElasticityMeasure	Shear modulus.
BendingStrength	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcPressureMeasure	Defining values: α; defined values: bending strength.
CompressiveStrength	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcPressureMeasure	Defining values: α; defined values: compressive strength.
TensileStrength	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcPressureMeasure	Defining values: α; defined values: tensile strength.
ShearStrength	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcPressureMeasure	Defining values: α; defined values: shear strength.
BearingStrength	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcPressureMeasure	Defining values: α; defined values: bearing strength of bolt holes, i.e. intrados pressure.
RaisedCompressiveStrength	P_SINGLEVALUE / IfcPressureMeasure	Alternative value for compressive strength which may be used under material and code dependent conditions (e.g. if deformation is tolerable, or far from ends of the member); conditions should be stated in SELFIfcProperty.Description.
ReferenceDepth	P_SINGLEVALUE / IfcPositiveLengthMeasure	Depth in bending for which the mechanical properties are valid; provided as a means to check the integrity of material assignment.

OutOfPlane

COMPLEX / CP_MaterialMechanicalPanel

Out Of Plane

Mechanical properties with respect to out-of-plane load, i.e. for function as a plate; tension zone of unbalanced layups is stressed in tension.

Name	Type	Description
YoungModulusBending	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcModulusOfElasticityMeasure	Defining values: α; defined values: elastic modulus in bending.
YoungModulusTension	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcModulusOfElasticityMeasure	Defining values: α; defined values: elastic modulus in tension.
YoungModulusCompression	P_SINGLEVALUE / IfcModulusOfElasticityMeasure	Elastic modulus in compression.
ShearModulus	P_SINGLEVALUE / IfcModulusOfElasticityMeasure	Shear modulus.
BendingStrength	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcPressureMeasure	Defining values: α; defined values: bending strength.
CompressiveStrength	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcPressureMeasure	Defining values: α; defined values: compressive strength.
TensileStrength	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcPressureMeasure	Defining values: α; defined values: tensile strength.
ShearStrength	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcPressureMeasure	Defining values: α; defined values: shear strength.
BearingStrength	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcPressureMeasure	Defining values: α; defined values: bearing strength of bolt holes, i.e. intrados pressure.
RaisedCompressiveStrength	P_SINGLEVALUE / IfcPressureMeasure	Alternative value for compressive strength which may be used under material and code dependent conditions (e.g. if deformation is tolerable, or far from ends of the member); conditions should be stated in SELFIfcProperty.Description.
ReferenceDepth	P_SINGLEVALUE / IfcPositiveLengthMeasure	Depth in bending for which the mechanical properties are valid; provided as a means to check the integrity of material assignment.

OutOfPlaneNegative

COMPLEX / CP_MaterialMechanicalPanel

Out Of Plane Negative

Mechanical properties with respect to out-of-plane load i.e. for function as a plate; compression zone of unbalanced layups is stressed in tension.

Name	Type	Description
YoungModulusBending	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcModulusOfElasticityMeasure	Defining values: α; defined values: elastic modulus in bending.
YoungModulusTension	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcModulusOfElasticityMeasure	Defining values: α; defined values: elastic modulus in tension.
YoungModulusCompression	P_SINGLEVALUE / IfcModulusOfElasticityMeasure	Elastic modulus in compression.
ShearModulus	P_SINGLEVALUE / IfcModulusOfElasticityMeasure	Shear modulus.
BendingStrength	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcPressureMeasure	Defining values: α; defined values: bending strength.
CompressiveStrength	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcPressureMeasure	Defining values: α; defined values: compressive strength.
TensileStrength	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcPressureMeasure	Defining values: α; defined values: tensile strength.
ShearStrength	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcPressureMeasure	Defining values: α; defined values: shear strength.
BearingStrength	P_TABLEVALUE / IfcPositivePlaneAngleMeasure / IfcPressureMeasure	Defining values: α; defined values: bearing strength of bolt holes, i.e. intrados pressure.
RaisedCompressiveStrength	P_SINGLEVALUE / IfcPressureMeasure	Alternative value for compressive strength which may be used under material and code dependent conditions (e.g. if deformation is tolerable, or far from ends of the member); conditions should be stated in SELFIfcProperty.Description.
ReferenceDepth	P_SINGLEVALUE / IfcPositiveLengthMeasure	Depth in bending for which the mechanical properties are valid; provided as a means to check the integrity of material assignment.

###################################