LoadRunner监控Linux的三种方法

方法一、LR + SiteScope/nmon

 

方法二、使用rstatd包

1、下载rpc.rstatd-4.0.1.tar.gz

2、解压缩

tar -zxvf rpc.rstatd-4.0.1.tar.gz

3、配置

./configure

4、编译

make

5、安装

make install

6、启动

rpc.rstatd

7、在LoadRunner中添加计数器



 



    average load :在过去的1分钟，的平均负载

    cpu utilization: cpu的使用率

    disk traffic: disk传输率

    paging rate： 每秒从磁盘读到物理内存，或者从物理内存写到页面文件的内存页数

    Swap-in rate: 每秒交换到内存的进程数

    Swap-out rate: 每秒从内存交换出来的进程





8、将服务设置为自动启动（Linux启动时自动启动这些服务）：

    vi /etc/rc.d/rc.local

  如：

    #rpc.rstatd--绝对路径

    /usr/local/sbin/rpc.rstatd



 

方法3、使用Shell脚本



使用Shell脚本收集Linux资源写入csv文件，再通过LR的Analysis导入csv文件（Tools - Extenal Monitors - Import Data... ）

 


Shell脚本如下所示：

#!/bin/bash
# (C) 2006 Mark Boddington, http://www.badpenguin.co.uk
# Licensed under the GNU GPL Version 2.

# ***** Version 0.2 *****
# TODO -- Create CSV parsing rules for the netstat.

# *****  Configuration *****
# set LOG to the directory you want to write the performance data to.
# set SLEEP to the number of seconds you want to sleep between samples
# set HDD to the number of had disks in your machine.

LOG=/home/mark/PerfMon/LIVE
SLEEP=10
HDD=2

HTYPE=$(uname -s)

genStat()
{
 now=$( date +%S )
 while [ "$now" -ne "30" ]
 do
  sleep 1
  now=$( date +%S )
 done
 while :;
 do
  dat=$(date +%Y%m%d,%H:%M:%S)
  day=$(date +%Y%m%d )
  iostat -x 1 2 |  sed -e"s/^/(.*/)/$dat /1/" | grep "[0-9]/." | tail -${HDD} >> ${LOG}/io.${day}.log &
  vmstat 1 2 | awk "{ print /"$dat/", /$0 }" | tail -1 >> ${LOG}/vm.${day}.log &
  netstat -i | grep -v Iface | awk "{ print /"$dat/", /$0 }" >> ${LOG}/netstat.${day}.log &
  uptime >> ${LOG}/uptime.${day}.log &
  sleep $SLEEP
 done
}

mkcsv()
{
 dat=$1

 if [ "$HTYPE" == "SunOS" ]
 then
 
  #IO CSV
  echo date,time,device,r/s,w/s,kr/s,kw/s,wait,actv,wsvc_t,asvc_t,%w,%b > ${LOG}/io.${dat}.csv
  cat ${LOG}/io.${dat}.log | egrep -v "extended|device" | awk '{ OFS=","; print $1,$12,$2,$3,$4,$5,$6,$7,$8,$9,$10,$11 }' >> ${LOG}/io.${dat}.csv
  #VM csv
  echo date,time,k[r],k[b],k[w],swap,free,pg[re],pg[mf],pg[pi],pg[po],pg[fr],pg[de],pg[sr],m0,m1,m2,m1,interupt,syscall,ctxswt,cpu[us],cpu[sys],cpu[idl] > ${LOG}/vm.${dat}.csv
  cat ${LOG}/vm.${dat}.log | awk '{for(l=1;l<23;l++) { printf("%s,", $l) }; print $23 }' >> ${LOG}/vm.${dat}.csv
  #uptime csv
  echo time,users,5min,10min,15min > ${LOG}/uptime.${dat}.csv
  cat ${LOG}/uptime.${dat}.log | awk '{ OFS=","; if ( $6 ~ /^[hm][ri]/) { print $1,$7,$11$12$13 } else if ( $6 ~/^user/) { print $1,$5,$9$10$11} else { print $1,$6,$10$11$12} }' >> ${LOG}/uptime.${dat}.csv

 elif [ "$HTYPE" == "Linux" ]
 then
  #IO CSV
  echo "date,time,device,rrqm/s,wrqm/s,r/s,w/s,rsec/s,wsec/s,rkB/s,wkB/s,avgrq-sz,avgqu-sz,await,svctm,%util" > ${LOG}/io.${dat}.csv
  cat ${LOG}/io.${dat}.log | egrep -v "extended|device" | awk '{for(l=1;l<15;l++) { printf("%s,", $l) }; print $15}' >> ${LOG}/io.${dat}.csv
  #VM csv
  echo date,time,r,b,swp,free,buff,cache,si,so,bi,bo,in,cs,us,sy,id,wa > ${LOG}/vm.${dat}.csv
  cat ${LOG}/vm.${dat}.log | awk '{for(l=1;l<17;l++) { printf("%s,", $l) }; print $17 }' >> ${LOG}/vm.${dat}.csv
  #uptime csv
  echo time,users,5min,10min,15min > ${LOG}/uptime.${dat}.csv
  cat ${LOG}/uptime.${dat}.log | awk '{ OFS=","; if ( $4 ~ /^min/) { print $1,$5,$9$10$11 } else { print $1,$4,$8$9$10} }' >> ${LOG}/uptime.${dat}.csv
 else

  echo "Hmmm - An unexpected error occured. Have you change the host type?"
 
 fi

}

if [ "$HTYPE" != "SunOS" -a "$HTYPE" != "Linux" ] 
then
 echo "Error - This script has no knowlege of the System $HTYPE"
 echo "        You will need to do some tweaking."
 exit
fi

case $1 in 

 run)
  genStat
  ;;
 csv)
  if [ $# -lt 2 ]
  then
   echo "Error - You must supply a date in the form YYYYMMDD"
   exit
  fi
  mkcsv $2
  ;;
 *)
  echo -e ":::: Usage ::::"
  echo -e "$0 run             : Collect stats"
  echo -e "$0 csv YYYYMMDD    : Generate CSV from stats"
  echo ""
  ;;
esac