zoukankan      html  css  js  c++  java
  • Arduino 3G shield using SoftwareSerial to control

    On the 3G shield, by default the power pin is on D8 and reset pin is on D9. Make it HIGH then it works.

    if you want to play this 3G shield using SoftwareSerial on Arduino, 

    Try this code:

    /*
    
    Change UART control ports from Tx0 / Rx1 to Tx2 / Rx3  using SoftwareSerial
    And reserve Tx0 / Rx1 for debugging
    
    */
    
    #include <SoftwareSerial.h>
    
    
    #define rxPin 6
    #define txPin 7
    
    #define power_pin 8
    #define reset_pin 9
    
    SoftwareSerial mySerial(rxPin, txPin); // RX, TX
    
    char AtCommand[] = "ATI
    ";
    void setup()  
    {
     // Open serial communications and wait for port to open:
     Serial.begin(115200);
     while (!Serial) {
       ; // wait for serial port to connect. Needed for Leonardo only
     }
      pinMode(rxPin, INPUT);
      pinMode(txPin, OUTPUT);
      
       // power on 3G module automatically
      pinMode(power_pin, OUTPUT);
      digitalWrite(power_pin, HIGH);  
      
      delay(5000);
      
      Serial.println(AtCommand);
    
     
      // set the data rate for the SoftwareSerial port
      mySerial.begin(115200);
      mySerial.println(AtCommand);
      //mySerial.write(AtCommand);
    }
    
    
    
    void loop() // run over and over
    {
      if (mySerial.available())
      {
        Serial.write(mySerial.read());
      }
      if (Serial.available())
      {
        mySerial.write(Serial.read());
      }
    }

    if you play with this 3G shield, and you want to enable power at the setup, and change the baud rate from 115200 to 9600 on your arduino when communicating with chip SIM5126E.

    Try this code:

    /*
    
    Change UART control ports from Tx0 / Rx1 to Tx2 / Rx3  using SoftwareSerial
    And reserve Tx0 / Rx1 for debugging
    
    */
    #include <SoftwareSerial.h>
    
    #define rxPin 6
    #define txPin 7
    #define baudrate 9600
    
    #define power_pin 8
    #define reset_pin 9
    
    
    SoftwareSerial mySerial(rxPin, txPin); // RX, TX
    
    char AtCommand[] = "ATI
    ";
    void setup()  
    {
      // Open serial communications and wait for port to open:
      Serial.begin(baudrate);
      while (!Serial) {
        ; // wait for serial port to connect. Needed for Leonardo only
      }
      pinMode(rxPin, INPUT);
      pinMode(txPin, OUTPUT);
      
      Serial.println(AtCommand);
    
      // set the data rate for the SoftwareSerial port
      Serial.println("wait 5s for modem to wake up");
      
      // power on 3G module automatically
      pinMode(power_pin, OUTPUT);
      digitalWrite(power_pin, HIGH);
      
      delay(5000);
      mySerial.begin(115200);
      mySerial.println("AT+IPR=9600
    "); // chnage baudrate to 9600 baud
      
      Serial.println("Changing baudrate");
      mySerial.begin(baudrate);
      mySerial.println(AtCommand);
    }
    
    void loop() // run over and over
    {
      if (mySerial.available())
      {
        Serial.write(mySerial.read());
      }
      if (Serial.available())
      {
        mySerial.write(Serial.read());
      }
    }
  • 相关阅读:
    Codeforces Round #279 (Div. 2) C. Hacking Cypher 机智的前缀和处理
    Codeforces Round #279 (Div. 2) A. Team Olympiad 水题
    Codeforces Round #279 (Div. 2) B
    利用Hog特征和SVM分类器进行行人检测
    opencv 支持向量机SVM分类器
    opencv hog算子
    NOIP 2008 传纸条 NOIP 2000 方块取数 多线程DP
    POJ 1654 Area 计算几何
    hihocoder #1015 KMP
    HDU 1722 Cake 数学题
  • 原文地址:https://www.cnblogs.com/spaceship9/p/4770196.html
Copyright © 2011-2022 走看看