Chipscope 仿真VmodCAM IIC程序：
目的：熟悉EDK中建立chipscope
注意：zedboard使用digilent USB下载时，chipscope不能和SDK同时使用，否则芯片会死机。要用仿真器烧写程序。
1：搭建硬件平台
硬件平台如下所示：具体的EDK设计流程参见XILINX大学workshop
搭建后的平台见下图，其中除了IIC和axi总线，其他的都不是必须的外设，并且添加chipscoe。可以根据自己设计添加栓出。然后Export Design，出到到SDK中，编写IIC控制程序
2：编写SDK软件
（IIC控制程序），也就是设置摄像头的寄存器，具体的控制参见DT9 datashhet
配置寄存器
0x30,0x00,0x00,0x00, // Chip version. Default 0x1580 !! only for read !! 0x33,0x86,0x05,0x01, // MCU Reset 0x32,0x90,0x00,0x01, // test pattern 0x32,0x92,0x00,0x00, // R pattern 0x32,0x94,0x00,0xff, // G pattern 0x32,0x96,0x00,0x00, // B pattern 0x33,0x86,0x05,0x00, // MCU Release from reset 0x32,0x14,0x0D,0x85, // Slew rate control, PCLK 5, D 5 0x34,0x1E,0x8F,0x09, // PLL control; bypassed, powered down 0x34,0x1C,0x02,0x30, // PLL dividers; M=80,N=2,fMCLK=fCLKIN*M/(N+1)/8=24MHz 0x34,0x1E,0x8F,0x09, // PLL control; Power-up PLL; wait 1ms after this! 0x34,0x1E,0x8F,0x08, // PLL control; Turn off bypass 0x32,0x02,0x00,0x08, // Standby control; Wake up
0x33,0x8C,0x27,0x97, // Output format; Context B shadow 0x33,0x90,0x00,0x20, // RGB with BT656 codes
0x33,0x8C,0x27,0x2F, // Sensor Row Start Context B 0x33,0x90,0x00,0x04, // 4 0x33,0x8C,0x27,0x33, // Sensor Row End Context B 0x33,0x90,0x04,0xBB, // 1211 0x33,0x8C,0x27,0x31, // Sensor Column Start Context B 0x33,0x90,0x00,0x04, // 4
0x33,0x8C,0x27,0x35, // Sensor Column End Context B 0x33,0x90,0x06,0x4B, // 1611 0x33,0x8C,0x27,0x07, // Output width; Context B 0x33,0x90,0x02,0x80, // 640 0x33,0x8C,0x27,0x09, // Output height; Context B 0x33,0x90,0x01,0xE0, // 480
0x33,0x8C,0x27,0x5F, // Crop X0; Context B 0x33,0x90,0x00,0x00, // 0 0x33,0x8C,0x27,0x63, // Crop Y0; Context B 0x33,0x90,0x00,0x00, // 0 0x33,0x8C,0x27,0x61, // Crop X1; Context B 0x33,0x90,0x06,0x40, // 1600 0x33,0x8C,0x27,0x65, // Crop Y1; Context B 0x33,0x90,0x04,0xB0, // 1200
0x33,0x8C,0x27,0x41, // Sensor_Fine_IT_min B 0x33,0x90,0x01,0x69, // 361 0x33,0x8C,0xA1,0x20, // Capture mode options 0x33,0x90,0x00,0xF2, // Turn on AWB, AE, HG, Video 0x33,0x8C,0xA1,0x03, // Refresh Sequencer Mode 0x33,0x90,0x00,0x02, // Capture 0x33,0x90,0x00,0x00, // Read until sequencer in mode 0 (run) 0x30,0x1A,0x02,0xCC, // reset/output control; parallel enable, drive pins, start streaming
/*****************************************************************************/
/**
* This function is initial the iic_0.
*
* @param None.
*
* @return The number of bytes sent.
*
* @note None.
*
****************************************************************************/
int IIC_Initial( XIic *IicInstance, u16 DeviceId)
{
XIic_Config *IICConfigPtr; /* Pointer to configuration data */
Xil_AssertNonvoid(IicInstance != NULL);
/*
* Initialize the IIC driver so that it is ready to use.
*/
IICConfigPtr = XIic_LookupConfig(DeviceId);
if (IICConfigPtr == (XIic_Config *) NULL) {
IicInstance->IsReady = 0;
return (XST_DEVICE_NOT_FOUND);
}
return XIic_CfgInitialize(IicInstance, IICConfigPtr,IICConfigPtr->BaseAddress);
}int Vmod_CameraA_IIC_Config()
{
unsigned ByteCount=0;
int i = 0;
u8 ReadCamera_ChipVersion_Add[2] = {0x30,0x00};
u8 ReadCamera_ChipVersion_Rdata[2];
u16 Chip_Version = 0;
printf("Here we go
");
printf("Config the Camera
");
read_camera_config(XPAR_CAMER_IIC_A_BASEADDR,ReadCamera_ChipVersion_Add,ReadCamera_ChipVersion_Rdata);
Chip_Version = (ReadCamera_ChipVersion_Rdata[0] << 8) | ReadCamera_ChipVersion_Rdata[1];
printf("Read Chip Version is:0x%x
",Chip_Version);
for(i=0;i<MT9D112_CONFIG_BUFFER_ROWS;i++)
{
ByteCount += XIic_Send(XPAR_CAMER_IIC_A_BASEADDR,CAMERA_ADDRESS_ID,MT9D112_CONFIG_BUFFER[i],4,XIIC_STOP);
}
if(MT9D112_CONFIG_BUFFER_ROWS*4 == ByteCount)
{
printf("Camera Initialize success
");
printf("Camera Initialize ByteCount is:%d
",ByteCount);
return ByteCount;
}
else printf("Camera Initialize fail
");
}
void read_camera_config (u32 BaseAddress, u8 *sub_addr, u8 *RdData)
{
u8 sent_byte_count;
u8 received_byte_count;
RdData[0] = 0;
RdData[1] = 0;
xil_printf("Read ");
sent_byte_count = XIic_Send(BaseAddress, 0x78>>1, sub_addr, 2, XIIC_STOP); //write sub-address
if (sent_byte_count != 2)
xil_printf("Sent %d bytes ", sent_byte_count);
received_byte_count = XIic_Recv(BaseAddress, 0x79>>1, RdData, 2, XIIC_STOP); //read 2 byte datas
if (received_byte_count != 2)
xil_printf("Received %d bytes
", received_byte_count);
else
xil_printf("0x%02x 0x%02x
", RdData[0], RdData[1]);
}3:ChipScope 调试
4 VmodCAM
硬件写地址0x78 读地址0x79
访问方式：
1、通过直接的硬件寄存器访问
2、通过驱动变量进行配置，这种配置都是靠R[0X338C]与R[0X3390]两个硬件寄存器间接访问，R[0X338C]是选择驱动变量的寄存器，R[0X3390]则是设置对应驱动变量的值。
图 1 驱动变量地址
供电与复位：
配置操作：
寄存器上电的初始值
首先就可以读取摄像头的ID 地址是R[0X3000],读取的ID应该是0X1580.
然后复位MCU
PLL 时钟配置：
PLL配置包括R[0X341C]用于PLL输出（PCLK）频率设置。PCLK = MCLK*M/((N+1)/8), R[0X341E]用于设置PLL工作与否 还有旁路有否。如果想要旁路掉PLL那么R[0X341E]【0】必须设置为1，如果有功耗要求，可以将R[0X341E]【1】设置为1来关闭PLL 。如果要打开PLL，那么以上两位必须设置为0.在默认情况下，都是关闭和旁路掉PLL的。
Any changes to PLL settings must be done with PLL bypassed (R0x341E[0]=1). （当需要修改PLL的参数时必须保持PLL在旁路状态）
PLL programming and power-up sequence is as follows:
1. Program PLL frequency settings, R0x341C (pll_m, pll_n) (master clock frequency is
equal to fVCO_pll/8). With default settings master clock frequency of 80 MHz is
obtained with fCLKIN=16MHz.
2. Power up PLL, R0x341E[1] = 0.
3. Wait for PLL settling time > 1ms.
4. Turn off PLL bypass, R0x341E[0] = 0.
唉！！感觉无比的失望！实验室让我失望，生活让我失望，是我没看透还是我看得太透彻了，如果上天是要我早点死亡，那么就请快点吧，我已经厌倦了这个社会，厌倦了这个地方，厌倦了每一个人每一件事，讨厌每一个人和每一件事，看不惯那些人的嘴脸，看不惯他们的有色眼镜。讨厌那些每天只靠嘴脸生活的人。一个错误的选择真的是可以改变一生，我真的是深深的体会到了，一个选择并不是至改变了这件事本身，而是接下来的一些列有关的事情，会让人越陷越深，越来越错误的走下去，霉运也会接踵而至。不是本命年那么简单。哎这些人的肤浅让我感觉很郁闷。现在我最想做的事情就是退学走人，什么都不想做。早日离开这个是非之地是最好的方法。我相信我已经读不完三年了。这基本是肯定了的。为什么会是这样的。实验室为什么会是现在这种状态，人多力量比蚂蚁还不如，管理员带几十个所谓的研究生，而且态度极其恶劣，真不知道这种学校何时能发展，我敢打赌，学校如果不注意培养学生，迟早有一天会灭亡的。腐朽之气充满整个校园。话说回来，关我什么事呢，我又不是玉皇大帝，改变不了什么现状，管他的，做自己事情，让别人说去吧。迟早有一天结果会是和我想的一样。只重视所谓的教学成果，不去实际钻研，迟早会失败的。我是得罪了谁啊，生活折磨我，身体折磨我。死不死由谁决定啊？如果我知道的话我一定会叫他早点把我勾上吧。