zoukankan      html  css  js  c++  java
  • How To Install Nginx on CentOS 7(转)

    How To Install Nginx on CentOS 7

    PostedJuly 22, 2014 427.4kviews NGINX CENTOS

    About Nginx

    Nginx is a high performance web server software. It is a much more flexible and lightweight program than Apache HTTP Server.

    This tutorial will teach you how to install and start Nginx on your CentOS 7 server.

     

    Prerequisites

    The steps in this tutorial require the user to have root privileges. You can see how to set that up by following steps 3 and 4 in the Initial Server Setup with CentOS 7 tutorial.

     

    Step One—Add Nginx Repository

    To add the CentOS 7 EPEL repository, open terminal and use the following command:

    sudo yum install epel-release
    
     

    Step Two—Install Nginx

    Now that the Nginx repository is installed on your server, install Nginx using the following yum command:

    sudo yum install nginx
    

    After you answer yes to the prompt, Nginx will finish installing on your virtual private server (VPS).

     

    Step Three—Start Nginx

    Nginx does not start on its own. To get Nginx running, type:

    sudo systemctl start nginx
    

    If you are running a firewall, run the following commands to allow HTTP and HTTPS traffic:

    sudo firewall-cmd --permanent --zone=public --add-service=http 
    sudo firewall-cmd --permanent --zone=public --add-service=https
    sudo firewall-cmd --reload
    

    You can do a spot check right away to verify that everything went as planned by visiting your server's public IP address in your web browser (see the note under the next heading to find out what your public IP address is if you do not have this information already):

    http://server_domain_name_or_IP/
    

    You will see the default CentOS 7 Nginx web page, which is there for informational and testing purposes. It should look something like this:

    CentOS 7 Nginx Default

    If you see this page, then your web server is now correctly installed.

    Before continuing, you will probably want to enable Nginx to start when your system boots. To do so, enter the following command:

    sudo systemctl enable nginx
    

    Congratulations! Nginx is now installed and running!

    How To Find Your Server's Public IP Address

    To find your server's public IP address, find the network interfaces on your machine by typing:

    ip addr
    
    1. lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
    
    . . .
    2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    
    . . .
    

    You may see a number of interfaces here depending on the hardware available on your server. The lointerface is the local loopback interface, which is not the one we want. In our example above, the eth0interface is what we want.

    Once you have the interface name, you can run the following command to reveal your server’s public IP address. Substitute the interface name you found above:

    ip addr show eth0 | grep inet | awk '{ print $2; }' | sed 's//.*$//'
    
     

    Server Root and Configuration

    If you want to start serving your own pages or application through Nginx, you will want to know the locations of the Nginx configuration files and default server root directory.

    Default Server Root

    The default server root directory is /usr/share/nginx/html. Files that are placed in there will be served on your web server. This location is specified in the default server block configuration file that ships with Nginx, which is located at /etc/nginx/conf.d/default.conf.

    Server Block Configuration

    Any additional server blocks, known as Virtual Hosts in Apache, can be added by creating new configuration files in /etc/nginx/conf.d. Files that end with .conf in that directory will be loaded when Nginx is started.

    Nginx Global Configuration

    The main Nginx configuration file is located at /etc/nginx/nginx.conf. This is where you can change settings like the user that runs the Nginx daemon processes, and the number of worker processes that get spawned when Nginx is running, among other things.

     

    See More

    Once you have Nginx installed on your cloud server, you can go on to install a LEMP Stack.

  • 相关阅读:
    小试SQLServer中的CLR特性
    转:memcached命令行参数说明
    2012年9月19日最新整理的日本产品(日货)名单!
    转:Memcached Java Client API详解
    刚写的一个小案例,实现多选的添加及删除
    SVG中的常用标签
    转:网页启用Gzip压缩 提高浏览速度
    SVG案例:著名的PostScript老虎图片
    SVG文档:SVG编程经典教程(转)
    实用技巧:利用SQL Server的扩展属性自动生成数据字典
  • 原文地址:https://www.cnblogs.com/zhenfei/p/7795487.html
Copyright © 2011-2022 走看看