zoukankan      html  css  js  c++  java
  • OSPF 多区域配置

    GNS3图标

    通过配置OSPF协议使网络互通。


    实验拓扑

    OSPF多区域配置

    如图所示连接,地址规划如下:

    名称 接口 IP地址
    R1 f1/0 192.168.10.1/24
    R1 f0/0 192.168.20.1/24
    R1 f0/1 192.168.50.2/24
    R2 f0/0 192.168.20.2/24
    R2 f0/1 192.168.30.1/24
    R3 f0/0 192.168.30.2/24
    R3 f0/1 192.168.40.1/24
    R3 f1/0 192.168.60.1/24
    R4 f0/0 192.168.40.2/24
    R4 f0/1 192.168.50.1/24
    PC1 e0 192.168.10.2/24
    PC2 e0 192.168.60.2/24

    配置方法

    R1(config)#router ospf 1
    R1(config-router)#router-id 1.1.1.1
    R1(config-router)#network 192.168.20.0 0.0.0.255 area 0
    R1(config-router)#network 192.168.50.0 0.0.0.255 area 0
    R1(config-router)#network 192.168.10.0 0.0.0.255 area 0
    R1(config-router)#ex
    

    配置过程

    配置接口 IP 地址

    • R1
    R1#conf t
    Enter configuration commands, one per line.  End with CNTL/Z.
    R1(config)#int f0/0
    R1(config-if)#ip add 192.168.20.1 255.255.255.0
    R1(config-if)#no sh
    R1(config-if)#ex
    R1(config)#int f0/1
    R1(config-if)#ip add 192.168.50.2 255.255.255.0
    R1(config-if)#no sh
    R1(config-if)#ex
    R1(config)#int f1/0
    R1(config-if)#ip add 192.168.10.1 255.255.255.0
    R1(config-if)#no sh
    R1(config-if)#ex
    R1(config)#do show ip int b
    Interface                  IP-Address      OK? Method Status                Protocol
    FastEthernet0/0            192.168.20.1    YES manual up                    up      
    FastEthernet0/1            192.168.50.2    YES manual up                    up      
    FastEthernet1/0            192.168.10.1    YES manual up                    up      
    
    • R2
    R2#conf t
    Enter configuration commands, one per line.  End with CNTL/Z.
    R2(config)#int f0/0
    R2(config-if)#ip add 192.168.20.2 255.255.255.0
    R2(config-if)#no sh
    R2(config-if)#ex
    R2(config)#int f0/1
    R2(config-if)#ip add 192.168.30.1 255.255.255.0
    R2(config-if)#no sh
    R2(config-if)#ex
    R2(config)#do show ip int b
    Interface                  IP-Address      OK? Method Status                Protocol
    FastEthernet0/0            192.168.20.2    YES manual up                    up      
    FastEthernet0/1            192.168.30.1    YES manual up                    up      
    
    • R3
    R3#conf t
    Enter configuration commands, one per line.  End with CNTL/Z.
    R3(config)#int f0/0
    R3(config-if)#ip add 192.168.30.2 255.255.255.0
    R3(config-if)#no sh
    R3(config-if)#ex
    R3(config)#int f0/1
    R3(config-if)#ip add 192.168.40.1 255.255.255.0
    R3(config-if)#no sh
    R3(config-if)#ex
    R3(config)#int f1/0
    R3(config-if)#ip add 192.168.60.1 255.255.255.0
    R3(config-if)#no sh
    R3(config-if)#ex
    R3(config)#do show ip int b
    Interface                  IP-Address      OK? Method Status                Protocol
    FastEthernet0/0            192.168.30.2    YES manual up                    up      
    FastEthernet0/1            192.168.40.1    YES manual up                    up      
    FastEthernet1/0            192.168.60.1    YES manual up                    up      
    
    • R4
    R4#conf t
    Enter configuration commands, one per line.  End with CNTL/Z.
    R4(config)#int f0/0
    R4(config-if)#ip add 192.168.40.2 255.255.255.0
    R4(config-if)#no sh
    R4(config-if)#ex
    R4(config)#int f0/1
    R4(config-if)#ip add 192.168.50.1 255.255.255.0
    R4(config-if)#no sh
    R4(config-if)#ex
    R4(config)#do show ip int b
    Interface                  IP-Address      OK? Method Status                Protocol
    FastEthernet0/0            192.168.40.2    YES manual up                    up      
    FastEthernet0/1            192.168.50.1    YES manual up                    up      
    

    配置 loopback IP 地址

    • R1
    R1(config)#int loopback 0
    R1(config-if)#ip add 1.1.1.1 255.255.255.255
    R1(config-if)#no sh
    R1(config-if)#ex
    R1(config)#do show ip int b
    Interface                  IP-Address      OK? Method Status                Protocol
    FastEthernet0/0            192.168.20.1    YES manual up                    up      
    FastEthernet0/1            192.168.50.2    YES manual up                    up      
    FastEthernet1/0            192.168.10.1    YES manual up                    up      
    Loopback0                  1.1.1.1         YES manual up                    up      
    R1(config)#do show ip route
    Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
           D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
           N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
           E1 - OSPF external type 1, E2 - OSPF external type 2
           i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
           ia - IS-IS inter area, * - candidate default, U - per-user static route
           o - ODR, P - periodic downloaded static route
    
    Gateway of last resort is not set
    
         1.0.0.0/32 is subnetted, 1 subnets
    C       1.1.1.1 is directly connected, Loopback0
    C    192.168.10.0/24 is directly connected, FastEthernet1/0
    C    192.168.20.0/24 is directly connected, FastEthernet0/0
    C    192.168.50.0/24 is directly connected, FastEthernet0/1
    
    • R2
    R2(config)#int loopback 0
    R2(config-if)#ip add 2.2.2.2 255.255.255.255
    R2(config-if)#no sh
    R2(config-if)#ex
    R2(config)#do show ip int b
    Interface                  IP-Address      OK? Method Status                Protocol
    FastEthernet0/0            192.168.20.2    YES manual up                    up      
    FastEthernet0/1            192.168.30.1    YES manual up                    up      
    Loopback0                  2.2.2.2         YES manual up                    up      
    R2(config)#do show ip route
    Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
           D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
           N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
           E1 - OSPF external type 1, E2 - OSPF external type 2
           i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
           ia - IS-IS inter area, * - candidate default, U - per-user static route
           o - ODR, P - periodic downloaded static route
    
    Gateway of last resort is not set
    
         2.0.0.0/32 is subnetted, 1 subnets
    C       2.2.2.2 is directly connected, Loopback0
    C    192.168.30.0/24 is directly connected, FastEthernet0/1
    C    192.168.20.0/24 is directly connected, FastEthernet0/0
    
    • R3
    R3(config)#int loopback 0
    R3(config-if)#ip add 3.3.3.3 255.255.255.255
    R3(config-if)#no sh
    R3(config-if)#ex
    R3(config)#do show ip int b
    Interface                  IP-Address      OK? Method Status                Protocol
    FastEthernet0/0            192.168.30.2    YES manual up                    up      
    FastEthernet0/1            192.168.40.1    YES manual up                    up      
    FastEthernet1/0            192.168.60.1    YES manual up                    up      
    Loopback0                  3.3.3.3         YES manual up                    up      
    R3(config)#do show ip route
    Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
           D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
           N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
           E1 - OSPF external type 1, E2 - OSPF external type 2
           i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
           ia - IS-IS inter area, * - candidate default, U - per-user static route
           o - ODR, P - periodic downloaded static route
    
    Gateway of last resort is not set
    
         3.0.0.0/32 is subnetted, 1 subnets
    C       3.3.3.3 is directly connected, Loopback0
    C    192.168.30.0/24 is directly connected, FastEthernet0/0
    C    192.168.60.0/24 is directly connected, FastEthernet1/0
    C    192.168.40.0/24 is directly connected, FastEthernet0/1
    
    • R4
    R4(config)#int loopback 0
    R4(config-if)#ip add 4.4.4.4 255.255.255.255
    R4(config-if)#no sh
    R4(config-if)#ex
    R4(config)#do show ip int b
    Interface                  IP-Address      OK? Method Status                Protocol
    FastEthernet0/0            192.168.40.2    YES manual up                    up      
    FastEthernet0/1            192.168.50.1    YES manual up                    up      
    Loopback0                  4.4.4.4         YES manual up                    up      
    R4(config)#do show ip route
    Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
           D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
           N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
           E1 - OSPF external type 1, E2 - OSPF external type 2
           i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
           ia - IS-IS inter area, * - candidate default, U - per-user static route
           o - ODR, P - periodic downloaded static route
    
    Gateway of last resort is not set
    
         4.0.0.0/32 is subnetted, 1 subnets
    C       4.4.4.4 is directly connected, Loopback0
    C    192.168.40.0/24 is directly connected, FastEthernet0/0
    C    192.168.50.0/24 is directly connected, FastEthernet0/1
    

    配置 OSPF

    • R1
    R1(config)#router ospf 1
    R1(config-router)#router-id 1.1.1.1
    R1(config-router)#network 192.168.20.0 0.0.0.255 area 0
    R1(config-router)#network 192.168.50.0 0.0.0.255 area 0
    R1(config-router)#network 192.168.10.0 0.0.0.255 area 0
    R1(config-router)#ex
    
    • R2
    R2(config)#router ospf 1
    R2(config-router)#router-id 2.2.2.2
    R2(config-router)#network 192.168.20.0 0.0.0.255 area 0
    R2(config-router)#network 192.168.30.0 0.0.0.255 area 1
    R2(config-router)#ex
    
    • R3
    R3(config)#router ospf 1
    R3(config-router)#router-id 3.3.3.3
    R3(config-router)#network 192.168.30.0 0.0.0.255 area 1
    R3(config-router)#network 192.168.40.0 0.0.0.255 area 1
    R3(config-router)#network 192.168.60.0 0.0.0.255 area 1
    R3(config-router)#ex
    
    • R4
    R4(config)#router ospf 1
    R4(config-router)#router-id 4.4.4.4
    R4(config-router)#network 192.168.40.0 0.0.0.255 area 1
    R4(config-router)#network 192.168.50.0 0.0.0.255 area 0
    R4(config-router)#ex
    

    查看路由表

    • R1
    R1(config)#do show ip route
    Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
           D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
           N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
           E1 - OSPF external type 1, E2 - OSPF external type 2
           i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
           ia - IS-IS inter area, * - candidate default, U - per-user static route
           o - ODR, P - periodic downloaded static route
    
    Gateway of last resort is not set
    
         1.0.0.0/32 is subnetted, 1 subnets
    C       1.1.1.1 is directly connected, Loopback0
    O IA 192.168.30.0/24 [110/20] via 192.168.20.2, 00:15:07, FastEthernet0/0
    O IA 192.168.60.0/24 [110/21] via 192.168.50.1, 00:00:41, FastEthernet0/1
                         [110/21] via 192.168.20.2, 00:00:41, FastEthernet0/0
    C    192.168.10.0/24 is directly connected, FastEthernet1/0
    O IA 192.168.40.0/24 [110/20] via 192.168.50.1, 00:05:52, FastEthernet0/1
    C    192.168.20.0/24 is directly connected, FastEthernet0/0
    C    192.168.50.0/24 is directly connected, FastEthernet0/1
    
    • R2
    R2(config)#do show ip route
    Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
           D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
           N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
           E1 - OSPF external type 1, E2 - OSPF external type 2
           i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
           ia - IS-IS inter area, * - candidate default, U - per-user static route
           o - ODR, P - periodic downloaded static route
    
    Gateway of last resort is not set
    
         2.0.0.0/32 is subnetted, 1 subnets
    C       2.2.2.2 is directly connected, Loopback0
    C    192.168.30.0/24 is directly connected, FastEthernet0/1
    O    192.168.60.0/24 [110/11] via 192.168.30.2, 00:01:09, FastEthernet0/1
    O    192.168.10.0/24 [110/11] via 192.168.20.1, 00:02:26, FastEthernet0/0
    O    192.168.40.0/24 [110/20] via 192.168.30.2, 00:10:33, FastEthernet0/1
    C    192.168.20.0/24 is directly connected, FastEthernet0/0
    O    192.168.50.0/24 [110/20] via 192.168.20.1, 00:06:15, FastEthernet0/0
    
    • R3
    R3(config)#do show ip route
    Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
           D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
           N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
           E1 - OSPF external type 1, E2 - OSPF external type 2
           i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
           ia - IS-IS inter area, * - candidate default, U - per-user static route
           o - ODR, P - periodic downloaded static route
    
    Gateway of last resort is not set
    
         3.0.0.0/32 is subnetted, 1 subnets
    C       3.3.3.3 is directly connected, Loopback0
    C    192.168.30.0/24 is directly connected, FastEthernet0/0
    C    192.168.60.0/24 is directly connected, FastEthernet1/0
    O IA 192.168.10.0/24 [110/21] via 192.168.40.2, 00:02:35, FastEthernet0/1
                         [110/21] via 192.168.30.1, 00:02:35, FastEthernet0/0
    C    192.168.40.0/24 is directly connected, FastEthernet0/1
    O IA 192.168.20.0/24 [110/20] via 192.168.30.1, 00:10:38, FastEthernet0/0
    O IA 192.168.50.0/24 [110/20] via 192.168.40.2, 00:06:34, FastEthernet0/1
    
    • R4
    R4(config)#do show ip route
    Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
           D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
           N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
           E1 - OSPF external type 1, E2 - OSPF external type 2
           i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
           ia - IS-IS inter area, * - candidate default, U - per-user static route
           o - ODR, P - periodic downloaded static route
    
    Gateway of last resort is not set
    
    O    192.168.30.0/24 [110/20] via 192.168.40.1, 00:06:51, FastEthernet0/0
    O    192.168.60.0/24 [110/11] via 192.168.40.1, 00:01:27, FastEthernet0/0
         4.0.0.0/32 is subnetted, 1 subnets
    C       4.4.4.4 is directly connected, Loopback0
    O    192.168.10.0/24 [110/11] via 192.168.50.2, 00:02:44, FastEthernet0/1
    C    192.168.40.0/24 is directly connected, FastEthernet0/0
    O    192.168.20.0/24 [110/20] via 192.168.50.2, 00:06:36, FastEthernet0/1
    C    192.168.50.0/24 is directly connected, FastEthernet0/1
    

    验证结果

    • 配置VPC的IP地址
    PC1> ip 192.168.10.2 192.168.10.1
    Checking for duplicate address...
    PC1 : 192.168.10.2 255.255.255.0 gateway 192.168.10.1
    
    PC2> ip 192.168.60.2 192.168.60.1
    Checking for duplicate address...
    PC1 : 192.168.60.2 255.255.255.0 gateway 192.168.60.1
    
    • 测试可以相互ping
    PC1> ping 192.168.60.2
    192.168.60.2 icmp_seq=1 timeout
    84 bytes from 192.168.60.2 icmp_seq=2 ttl=61 time=59.831 ms
    84 bytes from 192.168.60.2 icmp_seq=3 ttl=61 time=63.507 ms
    84 bytes from 192.168.60.2 icmp_seq=4 ttl=61 time=57.735 ms
    84 bytes from 192.168.60.2 icmp_seq=5 ttl=61 time=64.449 ms
    
    PC2> ping 192.168.10.2
    84 bytes from 192.168.10.2 icmp_seq=1 ttl=61 time=58.141 ms
    84 bytes from 192.168.10.2 icmp_seq=2 ttl=61 time=55.996 ms
    84 bytes from 192.168.10.2 icmp_seq=3 ttl=61 time=64.000 ms
    84 bytes from 192.168.10.2 icmp_seq=4 ttl=61 time=56.732 ms
    84 bytes from 192.168.10.2 icmp_seq=5 ttl=61 time=65.020 ms
    
  • 相关阅读:
    20131226
    20131225
    20131221
    20131216
    如何在电脑上监控安卓手机应用程序运行的CPU、内存等资源情况,并做成曲线图
    jmeter实现protobuf格式参数传输
    jmeter 如何发送上传文件接口请求
    windows 上搭建 sftp 服务器 --freesshd
    python3安装后,为什么一定要输入python.exe才可以进入
    nginx安装
  • 原文地址:https://www.cnblogs.com/llife/p/11632991.html
Copyright © 2011-2022 走看看