root@k101:/ # cat /sys/class/lcd/debug
Usage:
echo basic <h_active> <v_active> <h_period> <v_period> > debug ; write lcd basic config
echo type <lcd_type> <lcd_bits> > debug ; write lcd type & bits
echo clock <lcd_cl
k> <ss_level> <clk_pol> > debug ; write lcd clk (Hz)
echo sync <hs_width> <hs_backporch> <hs_pol> <vs_width> <vs_backporch> <vs_pol> > debug ; write lcd sync timing
echo valid <hvsync_valid> <de_valid> > debug ; enable lcd sync signals
data format:
<lcd_type> : 0=mipi, 1=lvds, 2=edp, 3=ttl
<lcd_bits> : 6=6bit(RGB18bit), 8=8bit(RGB24bit)
<ss_level> : lcd clock spread spectrum level (0~6), 0 for disable
<xx_pol> : 0=negative, 1=positive
<xx_valid> : 0=disable, 1=enable
echo ttl <rb_swap> <bit_swap> > debug ; write ttl RGB swap config
echo lvds <vswing_level> <lvds_repack> <pn_swap> > debug ; write lvds config
echo mdsi <bit_rate_min> <bit_rate_max> <factor> > debug ; write mipi-dsi config
echo edp <link_rate> <lane_count> <vswing_level> > debug ; write edp config
data format:
<xx_swap> : 0=normal, 1=swap
<vswing_level> : lvds support level 0~4 (Default=1); edp support level 0~3 (default=0)
<lvds_repack> : 0=JEIDA mode, 1=VESA mode
<pn_swap> : 0=normal, 1=swap lvds p/n channels
<bit_rate_xxx> : unit in MHz
<link_rate> : 0=1.62G, 1=2.7G
echo offset <h_sign> <h_offset> <v_sign> <v_offset> > debug ; write ttl display offset
echo dither <dither_user> <dither_ctrl> > debug ; write user dither ctrl config
echo vadj <brightness> <contrast> <saturation> > debug ; write video adjust config
data format:
<xx_sign> : 0=positive, 1=negative
<dither_user> : 0=disable user control, 1=enable user control
<dither_ctrl> : dither ctrl in Hex, such as 0x400 or 0x600
<brightness> : negative 0x1ff~0x101, positive 0x0~0xff, signed value in Hex, default is 0x0
<contrast> : 0x0~0xff, unsigned value in Hex, default is 0x80
<saturation> : 0x0~0x1ff, unsigned value in Hex, default is 0x100
echo write > debug ; update lcd driver
echo reset > debug ; reset lcd config & driver
echo read > debug ; read current lcd config
echo test <num> > debug ; bist pattern test, 0=pattern off, 1~7=different pattern
echo 0/1 > status ; 0=disable lcd; 1=enable lcd
cat status ; read current lcd status
Usage:
echo basic <h_active> <v_active> <h_period> <v_period> > debug ; write lcd basic config
echo type <lcd_type> <lcd_bits> > debug ; write lcd type & bits
echo clock <lcd_clk> <ss_level> <clk_pol> > debug ; write lcd clk (Hz)
echo sync <hs_width> <hs_backporch> <hs_pol> <vs_width> <vs_backporch> <vs_pol> > debug ; write lcd sync timing
echo valid <hvsync_valid> <de_valid> > debug ; enable lcd sync signals
data format:
<lcd_type> : 0=mipi, 1=lvds, 2=edp, 3=ttl
<lcd_bits> : 6=6bit(RGB18bit), 8=8bit(RGB24bit)
<ss_level> : lcd clock spread spectrum level (0~6), 0 for disable
<xx_pol> : 0=negative, 1=po
sitive
<xx_valid> : 0=disable, 1=enable
echo ttl <rb_swap> <bit_swap> > debug ; write ttl RGB swap config #echo ttl <0> <0> > debug
echo lvds <vswing_level> <lvds_repack> <pn_swap> > debug ; write lvds config
echo mdsi <bit_rate_min> <bit_rate_max> <factor> > debug ; write mipi-dsi config
echo edp <link_rate> <lane_count> <vswing_level> > debug ; write edp config
data format:
<xx_swap> : 0=normal, 1=swap
<vswing_level> : lvds support level 0~4 (Default=1); edp support level 0~3 (default=0)
<lvds_repack> : 0=JEIDA mode, 1=VESA mode
<pn_swap> : 0=normal, 1=swap lvds p/n channels
<bit_rate_xxx> : unit in MHz
<link_rate> : 0=1.62G, 1=2.7G
echo offset <h_sign> <h_offset> <v_sign> <v_offset> > debug ; write ttl display offset
echo dither <dither_user> <dither_ctrl> > debug ; write user dither ctrl config
echo vadj <brightness> <contrast> <saturation> > debug ; write video adjust config
data format:
<xx_sign> : 0=positive, 1=negative
<dither_user> : 0=disable user control, 1=enable user control
<dither_ctrl> : dither ctrl in Hex, such as 0x400 or 0x600
<brightness> : negative 0x1ff~0x101, positive 0x0~0xff, signed value in Hex, default is 0x0
<contrast> : 0x0~0xff, unsigned value in Hex, default is 0x80
<saturation> : 0x0~0x1ff, unsigned value in Hex, default is 0x100
echo write > debug ; update lcd driver
echo reset > debug ; reset lcd config & driver
echo read > debug ; read current lcd config
echo test <num> > debug ; bist pattern test, 0=pattern off, 1~7=different pattern
echo 0/1 > status ; 0=disable lcd; 1=enable lcd
cat status ; read current lcd status
root@k101:/sys/class/lcd # echo read > debug
[ 7258.061871@0] lcd driver version: 20140805c8
[ 7258.061871@0]
[ 7258.062388@0] LCD mode: CLAP070NJ02, TTL 6bit, 1024x600@50.0Hz
[ 7258.062388@0] lcd_clk 42.699MHz
[ 7258.062388@0] ss_level 0
[ 7258.062388@0] clk_pol 0
[ 7258.062388@0]
[ 7258.082124@0] h_period 1344
[ 7258.082124@0] v_period 635
[ 7258.082124@0] hs_width 10
[ 7258.082124@0] hs_backporch 160
[ 7258.082124@0] hs_pol 0
[ 7258.082124@0] vs_width 5
[ 7258.082124@0] vs_backporch 23
[ 7258.082124@0] vs_pol 0
[ 7258.082124@0] vs_h_phase 0
[ 7258.082124@0] hvsync_valid 1
[ 7258.082124@0] de_valid 1
[ 7258.082124@0] h_offset 0
[ 7258.082124@0] v_offset 0
[ 7258.082124@0]
[ 7258.129269@0] rb_swap 0
[ 7258.129269@0] bit_swap 0
[ 7258.129269@0]
[ 7258.134175@0] pll_ctrl 0x01000438
[ 7258.134175@0] div_ctrl 0x00018833
[ 7258.134175@0] clk_ctrl 0x8eee1002
[ 7258.134175@0] video_on_pixel 300
[ 7258.134175@0] video_on_line 35
[ 7258.134175@0]
cd /sys/devices/platform/backlight/backlight/aml-bl/brightness
echo sync <hs_width> <hs_backporch> <hs_pol> <vs_width> <vs_backporch> <vs_pol> > debug
echo sync 10 160 0 5 23 0 > debug
Usage:
echo basic <h_active> <v_active> <h_period> <v_period> > debug ; write lcd basic config
echo type <lcd_type> <lcd_bits> > debug ; write lcd type & bits
echo clock <lcd_cl
k> <ss_level> <clk_pol> > debug ; write lcd clk (Hz)
echo sync <hs_width> <hs_backporch> <hs_pol> <vs_width> <vs_backporch> <vs_pol> > debug ; write lcd sync timing
echo valid <hvsync_valid> <de_valid> > debug ; enable lcd sync signals
data format:
<lcd_type> : 0=mipi, 1=lvds, 2=edp, 3=ttl
<lcd_bits> : 6=6bit(RGB18bit), 8=8bit(RGB24bit)
<ss_level> : lcd clock spread spectrum level (0~6), 0 for disable
<xx_pol> : 0=negative, 1=positive
<xx_valid> : 0=disable, 1=enable
echo ttl <rb_swap> <bit_swap> > debug ; write ttl RGB swap config
echo lvds <vswing_level> <lvds_repack> <pn_swap> > debug ; write lvds config
echo mdsi <bit_rate_min> <bit_rate_max> <factor> > debug ; write mipi-dsi config
echo edp <link_rate> <lane_count> <vswing_level> > debug ; write edp config
data format:
<xx_swap> : 0=normal, 1=swap
<vswing_level> : lvds support level 0~4 (Default=1); edp support level 0~3 (default=0)
<lvds_repack> : 0=JEIDA mode, 1=VESA mode
<pn_swap> : 0=normal, 1=swap lvds p/n channels
<bit_rate_xxx> : unit in MHz
<link_rate> : 0=1.62G, 1=2.7G
echo offset <h_sign> <h_offset> <v_sign> <v_offset> > debug ; write ttl display offset
echo dither <dither_user> <dither_ctrl> > debug ; write user dither ctrl config
echo vadj <brightness> <contrast> <saturation> > debug ; write video adjust config
data format:
<xx_sign> : 0=positive, 1=negative
<dither_user> : 0=disable user control, 1=enable user control
<dither_ctrl> : dither ctrl in Hex, such as 0x400 or 0x600
<brightness> : negative 0x1ff~0x101, positive 0x0~0xff, signed value in Hex, default is 0x0
<contrast> : 0x0~0xff, unsigned value in Hex, default is 0x80
<saturation> : 0x0~0x1ff, unsigned value in Hex, default is 0x100
echo write > debug ; update lcd driver
echo reset > debug ; reset lcd config & driver
echo read > debug ; read current lcd config
echo test <num> > debug ; bist pattern test, 0=pattern off, 1~7=different pattern
echo 0/1 > status ; 0=disable lcd; 1=enable lcd
cat status ; read current lcd status
Usage:
echo basic <h_active> <v_active> <h_period> <v_period> > debug ; write lcd basic config
echo type <lcd_type> <lcd_bits> > debug ; write lcd type & bits
echo clock <lcd_clk> <ss_level> <clk_pol> > debug ; write lcd clk (Hz)
echo sync <hs_width> <hs_backporch> <hs_pol> <vs_width> <vs_backporch> <vs_pol> > debug ; write lcd sync timing
echo valid <hvsync_valid> <de_valid> > debug ; enable lcd sync signals
data format:
<lcd_type> : 0=mipi, 1=lvds, 2=edp, 3=ttl
<lcd_bits> : 6=6bit(RGB18bit), 8=8bit(RGB24bit)
<ss_level> : lcd clock spread spectrum level (0~6), 0 for disable
<xx_pol> : 0=negative, 1=po
sitive
<xx_valid> : 0=disable, 1=enable
echo ttl <rb_swap> <bit_swap> > debug ; write ttl RGB swap config #echo ttl <0> <0> > debug
echo lvds <vswing_level> <lvds_repack> <pn_swap> > debug ; write lvds config
echo mdsi <bit_rate_min> <bit_rate_max> <factor> > debug ; write mipi-dsi config
echo edp <link_rate> <lane_count> <vswing_level> > debug ; write edp config
data format:
<xx_swap> : 0=normal, 1=swap
<vswing_level> : lvds support level 0~4 (Default=1); edp support level 0~3 (default=0)
<lvds_repack> : 0=JEIDA mode, 1=VESA mode
<pn_swap> : 0=normal, 1=swap lvds p/n channels
<bit_rate_xxx> : unit in MHz
<link_rate> : 0=1.62G, 1=2.7G
echo offset <h_sign> <h_offset> <v_sign> <v_offset> > debug ; write ttl display offset
echo dither <dither_user> <dither_ctrl> > debug ; write user dither ctrl config
echo vadj <brightness> <contrast> <saturation> > debug ; write video adjust config
data format:
<xx_sign> : 0=positive, 1=negative
<dither_user> : 0=disable user control, 1=enable user control
<dither_ctrl> : dither ctrl in Hex, such as 0x400 or 0x600
<brightness> : negative 0x1ff~0x101, positive 0x0~0xff, signed value in Hex, default is 0x0
<contrast> : 0x0~0xff, unsigned value in Hex, default is 0x80
<saturation> : 0x0~0x1ff, unsigned value in Hex, default is 0x100
echo write > debug ; update lcd driver
echo reset > debug ; reset lcd config & driver
echo read > debug ; read current lcd config
echo test <num> > debug ; bist pattern test, 0=pattern off, 1~7=different pattern
echo 0/1 > status ; 0=disable lcd; 1=enable lcd
cat status ; read current lcd status
root@k101:/sys/class/lcd # echo read > debug
[ 7258.061871@0] lcd driver version: 20140805c8
[ 7258.061871@0]
[ 7258.062388@0] LCD mode: CLAP070NJ02, TTL 6bit, 1024x600@50.0Hz
[ 7258.062388@0] lcd_clk 42.699MHz
[ 7258.062388@0] ss_level 0
[ 7258.062388@0] clk_pol 0
[ 7258.062388@0]
[ 7258.082124@0] h_period 1344
[ 7258.082124@0] v_period 635
[ 7258.082124@0] hs_width 10
[ 7258.082124@0] hs_backporch 160
[ 7258.082124@0] hs_pol 0
[ 7258.082124@0] vs_width 5
[ 7258.082124@0] vs_backporch 23
[ 7258.082124@0] vs_pol 0
[ 7258.082124@0] vs_h_phase 0
[ 7258.082124@0] hvsync_valid 1
[ 7258.082124@0] de_valid 1
[ 7258.082124@0] h_offset 0
[ 7258.082124@0] v_offset 0
[ 7258.082124@0]
[ 7258.129269@0] rb_swap 0
[ 7258.129269@0] bit_swap 0
[ 7258.129269@0]
[ 7258.134175@0] pll_ctrl 0x01000438
[ 7258.134175@0] div_ctrl 0x00018833
[ 7258.134175@0] clk_ctrl 0x8eee1002
[ 7258.134175@0] video_on_pixel 300
[ 7258.134175@0] video_on_line 35
[ 7258.134175@0]
cd /sys/devices/platform/backlight/backlight/aml-bl/brightness
echo sync <hs_width> <hs_backporch> <hs_pol> <vs_width> <vs_backporch> <vs_pol> > debug
echo sync 10 160 0 5 23 0 > debug