zoukankan      html  css  js  c++  java
  • How to debug Bluetooth

    Where are the logs?

    Whatare needed to debug Bluetooth?

    1. Overview of bluetooth stacks architecture.
    2. You should know which layer has issue.
    3. Read Bluetooth specification careful if you need.
    4. Cross analyze logs, codes and spec.

    There are hcidump, air sniffer log, Bluetooth kernel stack log, bluetoothd print log and android logcat. In general case, they are needed to debug Bluetooth issues.

    The figure like this:


     

    How touse frontline to capture the Bluetooth air log?

    Introduction

    FTS4BT™ is a PC‐based, Bluetooth® protocol analyzer that displaysclassic Bluetooth data in Frontline's intuitive display, simplifying andaccelerating the debugging process.

    1.   Hardware.

    Purchasethem from frontline companyJ

    1.   Software

    DownloadFTS4BT from:

    http://www.fte.com/support/CPAS-download.aspx?demo=FTS4BT&iid=16

    2.   Installthe FTS4BT.
    1) Plug in the FTS dongle into computer.
    2) Pls install the FTS4BT, it is very easy.

    OPENING/SELECTING DATA CAPTURE METHOD

    Nowthat the devices are on, the ComProbe positioned correctly, the next step is toopen FTS4BT and select the data capture method.

    1.   Open "Frontline FTS4BT"from the Start menu or from the Desktop folder.

    Select"Frontline FTS4BT".


    Expand the tree for " Bluetooth AirSniffing" 

    1.   Select "Single Connection(Air Basic)".

    Select"Run". 

    HARDWARE SETTINGS

    Select"Hardware Settings" 


    Choose a Bluetooth® ComProbe® device.



    I/O SETTINGS

    Turn on Devices

    Beforeyou actually configure I/O Settings, you have to turn on the devices that youwant to test.

    1.   Make the device(s) discoverable.The process will be different for every device.
    IMPORTANT NOTE: If youcan’t make your device discoverable, the BD_ADDR may be entered manually. Youwill have the chance to do that later in the process.

    ClockSynchronization

    TheBluetooth analyzer needs to know how to synchronize with the piconet.The analyzer supports two Synchronization Modes: Standard (Slave Page) andAlternate – Slave must be Discoverable (Slave Inquiry)

    1.   Select Standard (Slave Page)

    This is thepreferred synchronization mode to use. This is how Frontline learns the clockof a device that is NOT discoverable. For example, after a phone and a headsethave paired, often the headset will not be discoverable. If the headset is aslave device and it is not discoverable, then FTS4BT will not be able tosynchronize to that device using Slave Inquiry mode. If we know the headset(slave) BD‐ADDR then by using SlavePage mode, FTS4BT will be able to page the device, (but will never complete theconnection during the page session). Once FTS4BT learns the clock informationduring the paging process, FTS4BT will discontinue the paging process and willnow be synchronized to the undiscoverable slave’s clock.

    SlavePage is highly recommended, especially when the link is encrypted

    SynchronizationDevice
    NowFTS4BT needs to know the Bluetooth Device Address (BD_ADDR) of thesynchronizing devices.

    2.   Select the "DiscoverDevices" button 

    FTS4BTwill go out and locate all the discoverable Bluetooth devices. The devices that you made discoverable a few moments ago should appear in the list

    1.   Click on the drop‐down arrow for Master and select the device address for the telephone 

    1.   Click on the drop‐down arrow for Slave and select the device address for the ear piece 

    It'simportant to remember here that the Master is always the device which initiatesthe connection.

    Click on the drop‐down arrow for Slave and select the deviceaddress for the ear piece 

    Encryption

    Once you have identified the Master and Slave, the next step is tochoose encryption.

    l  None

    l  PINCode (ASCII)

    l  PINCode (Hex)

    l  LinkKey

    l  First,you can choose "None" as the encryption method when neither of thedevices has encryption enabled.

    l  Thesecond and third ways are to use a PIN Code to generate the Link Key. Thedevices generate link Keys during the Pairing Process based on a PIN Code. TheLink Key generated from this process is also based on a random number so thesecurity cannot be compromised. If the analyzer is given the PIN Code it candetermine the Link Key using the same algorithm. Since the analyzer also needsthe random number, the analyzer must catch the entire Pairing Process or elseit cannot generate the Link Key and decode the data.

    l  Fourth,if you know the Link Key in advance you may enter it directly. Select LinkKey in the Encryption list and then enter the Link Key in the edit box. Ifthe link key is already in the database, the Link Key is automatically enteredin the edit box after the Master and Slave have been selected. You can alsopick Choose Pair from Device Database to select a Master, Slave and LinkKey from the Device Database.

    1.   Select "PIN Code(ASCII)"

    2.   Enter the "ASCII PINCode"

    3.   Click OK to close I/OSettings

    4.   Start the pairing process betweenthe devices. The pairing process will vary from device to device 



    START SNIFFING

    ANALYZING DATA

    Control Window


    FrameDisplay

    Clickframe display icon, 

    How touse hcidump?

    DESCRIPTION

    hcidump  reads raw HCI data coming from and going to aBluetooth device

           (which canbe specified with the option -i, default is the first avail-

           able  one) and  prints to screen commands,events and data in a human-

           readableform. Optionally, the dump can be written to  a  file rather

           than parsed,and the dump file can be parsed in a subsequent moment.

    OPTIONS

    Usage:hcidump [OPTION...] [filter]

      -i, --device=hci_dev       HCI device

      -l, --snap-len=len         Snap len (in bytes)

      -p, --psm=psm              Default PSM

      -m, --manufacturer=compid  Default manufacturer

      -w, --save-dump=file       Save dump to a file

      -r, --read-dump=file       Read dump from a file

      -d, --wait-dump=host       Wait on a host and send

      -t, --ts                   Display time stamps

      -a, --ascii                Dump data in ascii

      -x, --hex                  Dump data in hex

      -X, --ext                  Dump data in hex and ascii

      -R, --raw                  Dump raw data

      -C, --cmtp=psm             PSM for CMTP

      -H, --hcrp=psm             PSM for HCRP

      -O, --obex=channel         Channel for OBEX

      -P, --ppp=channel          Channel for PPP

      -D, --pppdump=file         Extract PPP traffic

      -A, --audio=file           Extract SCO audio data

      -Y, --novendor             No vendor commands or events

      -4, --ipv4                 Use IPv4 as transport

      -6 --ipv6                 Use IPv6 astransport

      -h, --help                 Give this help list

      -v, --version              Give version information

          --usage                Give a short usage message

    USEAGE STEPS

    1.   Install hcidump on debug board.AtPC develop directory:
    ~/workspace/dkbtd-gingerbread$ adb pushout/target/product/dkb/system/xbin/hcidump /system/xbin/

    2.   Enable BT on debug board

    3.   Run “hcidump –w hci.cfa” atdebug board’s sdcard directory

    4.   Do your test

    5.   On PC side, pull out the hcidumpdata: $ adb pull /sdcard/hci.cfa ./

    OpenFTS’s “Capture file viewer” from start menu ordesktop

    1.   Click open icon , choose your capture data file,like this:

     Click show frame display icon ,

    Showthe frames:



    PS:

    Ifyou don’t have FTS, you can check the hcidump data use “hcidump -r hci.cfa -tV”. There is a sample:

    sxxu@sxxu-desktop:~/tmp$hcidump -r hci1.cfa -tV

    HCIsniffer - Bluetooth packet analyzer ver 1.42

    2000-01-0415:46:43.240234 < ACL data: handle 1 flags 0x00 dlen 12

    2000-01-0415:46:43.240264 < HCI Command: Exit Sniff Mode (0x02|0x0004) plen 2

        handle 1

    2000-01-0415:46:43.247741 > HCI Event: Command Status (0x0f) plen 4

        Exit Sniff Mode (0x02|0x0004) status 0x00ncmd 1

    2000-01-0415:46:43.384490 > HCI Event: Number of Completed Packets (0x13) plen 5

        handle 1 packets 1

    2000-01-0415:46:43.388122 > ACL data: handle 1 flags 0x02 dlen 16

        L2CAP(s): Connect rsp: dcid 0x005f scid0x0041 result 1 status 2

          Connection pending - Authorizationpending

    2000-01-0415:46:43.390136 > HCI Event: Mode Change (0x14) plen 6

        status 0x00 handle 1 mode 0x00 interval 0

        Mode: Active

    2000-01-0415:46:43.398040 > ACL data: handle 1 flags 0x02 dlen 16

        L2CAP(s): Connect rsp: dcid 0x005f scid 0x0041result 0 status 0

          Connection successful

    2000-01-0415:46:43.398101 < ACL data: handle 1 flags 0x00 dlen 16

    2000-01-0415:46:43.400512 > HCI Event: Number of Completed Packets (0x13) plen 5

        handle 1 packets 1

    2000-01-0415:46:43.407409 > ACL data: handle 1 flags 0x02 dlen 14

        L2CAP(s): Config rsp: scid 0x0041 flags0x00 result 0 clen 0

          Success

    2000-01-0415:46:43.407958 > ACL data: handle 1 flags 0x02 dlen 16

        L2CAP(s): Config req: dcid 0x0041 flags0x00 clen 4

          MTU 1013

    How tocapture the bluez print log?

    LogcatalsoJ

    How toseparate the logs? 





  • 相关阅读:
    后端开发应该掌握的 Redis 基础
    Code Review有什么好处?
    对不起,你那不叫努力,叫重复劳动
    老鸟程序员才知道的40个小技巧
    单例模式基础笔记
    最受IT公司欢迎的50款开源软件
    硬件:关于路由器、交换机、宽带猫的几个问题
    硬件:宽带猫(光猫)的基础知识
    python selenium模块使用出错解决,Message: ‘geckodriver’ executable needs to be in PATH
    python+selenium如何定位页面的元素,的几种定位元素的方法。
  • 原文地址:https://www.cnblogs.com/javawebsoa/p/2989603.html
Copyright © 2011-2022 走看看