相关软件下载地址：http://pan.baidu.com/s/16yo8Y
fsc100开发板
交叉编译工具：arm-cortex_a8-linux-gnueabi-gcc
添加针对我们平台的Nand flash驱动
拷贝s3c_nand.c到drivers/mtd/nand下
拷贝regs-nand.h到arch/arm/mach-s5pc100/include/mach下
针对平台上的nand flash设备，修改drivers/mtd/nand/nand_base.c第2812行
for (i = 0; i < 5; i++)
- 添加内核配置选项
修改drivers/mtd/nand/Kconfig，在if mtd_nand下面添加如下内容：
config MTD_NAND_S3C
tristate "NAND Flash support for S3C SoC"
depends on (ARCH_S3C64XX || ARCH_S5P64XX || ARCH_S5PC1XX || ARCH_S5PC100) && MTD_NAND
help
This enables the NAND flash controller on the S3C.
No board specfic support is done by this driver, each board
must advertise a platform_device for the driver to attach.
config MTD_NAND_S3C_DEBUG
bool "S3C NAND driver debug"
depends on MTD_NAND_S3C
help
Enable debugging of the S3C NAND driver
config MTD_NAND_S3C_HWECC
bool "S3C NAND Hardware ECC"
depends on MTD_NAND_S3C
help
Enable the use of the S3C's internal ECC generator when
using NAND. Early versions of the chip have had problems with
incorrect ECC generation, and if using these, the default of
software ECC is preferable.
If you lay down a device with the hardware ECC, then you will
currently not be able to switch to software, as there is no
implementation for ECC method used by the S3C
修改drivers/mtd/nand/Makefile添加如下内容：
obj-$(CONFIG_MTD_NAND_S3C) += s3c_nand.o
- 修改平台代码
修改arch/arm/mach-s5pc100/mach-smdkc100.c添加如下内容：
- 添加头文件
#if defined (CONFIG_MTD_NAND_S3C)
#include <linux/mtd/partitions.h>
#include <linux/mtd/mtd.h>
#include <plat/nand.h>
#endif
- 添加平台设备
#if defined(CONFIG_MTD_NAND_S3C)
/* Nand Flash Support */
static struct mtd_partition s5pc100_nand_part[] = {
[0] = {
.name = "bootloader",
.size = SZ_1M,
.offset = 0,
},
[1] = {
.name = "kernel",
.offset = MTDPART_OFS_APPEND,
.size = SZ_1M*3,
},
[2] = {
.name = "rootfs",
.offset = MTDPART_OFS_APPEND,
.size = SZ_4M,
},
[3] = {
.name = "usrfs",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
},
};
struct s3c_nand_mtd_info s5pc100_nand_mtd_part_info = {
.chip_nr = 1,
.mtd_part_nr = ARRAY_SIZE(s5pc100_nand_part),
.partition = s5pc100_nand_part,
};
static struct resource s5pc100_nand_resource[] = {
[0] = {
.start = 0xE7200000,
.end = 0xE7200000 + SZ_1M,
.flags = IORESOURCE_MEM,
}
};
struct platform_device s5pc100_device_nand = {
.name = "s5pc100-nand",
.id = -1,
.num_resources = ARRAY_SIZE(s5pc100_nand_resource),
.resource = s5pc100_nand_resource,
.dev = {
.platform_data = &s5pc100_nand_mtd_part_info,
}
};
#endif
- 添加平台设备列表
在smdkc100_device[]结构体数组中添加如下内容：
#if defined(CONFIG_MTD_NAND_S3C)
&s5pc100_device_nand,
#endif
- 修改arch/arm/plat-samsung/include/plat/nand.h添加如下内容：
struct s3c_nand_mtd_info {
uint chip_nr;
uint mtd_part_nr;
struct mtd_partition *partition;
};
- 配置内核
$ make menuconfig
Device Drivers --->
<*> Memory Technology Device (MTD) support --->
[*] MTD partitioning support
<*> Caching block device access to MTD devices
<*> NAND Device Support --->
<*> NAND Flash support for S3C SoC
[*] S3C NAND Hardware ECC
File Systems --->
Partition Types --->
[*] Advanced partition selection
[*] PC BIOS (MSDOS partition tables) support
[*] BSD disklabel (FreeBSD partition tables) support
- 编译内核并拷贝到tftpboot下
$ make zImage
$ cp arch/arm/boot/zImage /tftpboot
- 测试
启动目标板，在目标板上完成如下操作：
# cat /proc/mtd
dev: size erasesize name
mtd0: 00100000 00020000 "bootloader"
mtd1: 00300000 00020000 "kernel"
mtd2: 00400000 00020000 "rootfs"
mtd3: 0f800000 00020000 "usrfs"